Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
(8) COPY function Besides camera title, PTZ ID and INSTALLED/COVERT, the settings can be copied from one camera to another. Select the camera to be copied from the camera list on the left and press the COPY key. The message “COPIED” appears at the top screen margin. Select the camera which shall apply the settings from the camera list. Press the SEARCH key to assign the copied settings to the camera. The message “PASTED” appears at the top screen margin. 33 3.3 RECORDING MENU RECORDING RECORD AUDIO YES TIME STAMP OFF TIME STAMP POS. BOTTOM WATERMARK OFF WATERMARK POS. TOP RESOLUTION 720X288 RECORD MODE REWRITE Define the following settings in the recording menu: (1) RECORD AUDIO: YES: Audio is recorded together with video. Audio recording is effected independent of image recording rate. NO: Audio recording is deactivated. (2) TIME STAMP: ON: Recording is overlaid by time and date. OFF: Recording doesn’t provide time/date stamp. (3) TIME STAMP POS.: TOP: Time / date is displayed at the top screen margin. BOTTOM: Time / date is displayed at the bottom screen margin. (4) WATERMARK : ON: Recording is overlaid by a visible watermark ("W"). OFF: No watermark. 34 (5) RESOLUTION: DVR PAL recording resolution is adjustable as follows: 720x288 (Half D1), Default setting, total recording rate 100 IPS for EDR920 total recording rate 200 IPS for EDR1640 720x576 (D1) , total recording rate 50 IPS for EDR920 total recording rate 100 IPS for EDR1640 or 360x288 (CIF) , total recording rate 200 IPS for EDR920 total recording rate 400 IPS for EDR1640 (6) RECORD MODE: REWRITE: If the harddisk is full, the DVR starts to overwrite the harddisk, previous recordings are deleted automatically. STOP: If the harddisk is full, the DVR stops recording (for signalling, refer to WARNING menu). 35 3.4 ALARM MENU ALARM ALARM ENABLE ALARM TYPE N.O. ALARM 3 ALARM 4 ACTIVE CAMERA 01 ALARM 5 DURATION 05 SEC ALARM 6 ALARM OUTPUT NONE ALARM 7 ALARM EMAIL NO ALARM 8 BUZZER OFF ALARM 9 ALARM NETWORK NO SUMMARY MAIN MON NO CHANGE CALL MON NO CHANGE MATRIX 1 NO CHANGE MATRIX 2 NO CHANGE MATRIX 3 NO CHANGE MATRIX 4 NO CHANGE ALARM 1 ALARM 2 Menu display for EDR-920, EDR1640 identical, but with 16 alarm inputs. Define the dry alarm contacts’ attributes and the alarm reactions in the ALARM menu. For alarm contact pin assignment, please refer to appendix D. Each contact is adjusted individually and selected from the list on the left: (1) ALARM: ENABLE: Contact is activated. DISABLE: Contact is deactivated. (2) ALARM TYPE: N.O. : Normally open, contact reacts on being connected to ground (GND). Define the alarm duration within menu item DURATION. N.C.: Normally closed, contact reacts on being disconnected from ground (GND). Define the alarm duration within menu item DURATION. N.O. + Trans.: Transparent mode, similar to normally open but: alarm is active as long as input contact (but minimal as defined in DURATION) N.C. + Trans.: Transparent mode, similar to normally closed but: alarm is active as long as input contact (but minimal as defined in DURATION) (3) ACTIVE CAMERA: Alarm camera being recorded and displayed in full screen on the main monitor (see (10) MAIN MONITOR). Recording is carried out according to the settings defined for EVENT within the CAMERA menu. COPY function Alarm settings can be copied from one contact to another. Select the contact to be copied from the contact list on the left and press the COPY key. The message “COPIED” appears at the top screen margin. Select the contact which shall apply the settings from the contact list. Press the SEARCH key to assign the copied settings to the contact. The message “PASTED” appears at the top screen margin 36 (4) DURATION: Alarm duration for N.O. and N.C. contact types. Duration applies to recording, screen change, buzzer and output contact and is adjustable from 1~99 seconds. (5) ALARM OUTPUT: Output relay activation. 1: Output relay 1~4 (selection) is switched in case of alarm NONE: Output relay is deactivated. (6) ALARM EMAIL: By selecting “ON”, an email is sent in case of alarm, containing the alarm message, the camera’s alarm image and the DVR IP address as sender. Define the email recipiant’s details in the NETWORK menu. (7) BUZZER: Alarm buzzer activation ENABLE: Alarm buzzer is activated. DISABLE: Alarm buzzer is deactivated. (8) ALARM NETWORK: Network alarm function activation. Network alarm reception requires installation of the optionally available PowerCon software. The network alarm transmits both the alarm message and the DVR IP address as sender to up to 3 recipiants. YES: Network alarm is activated. NO: Network alarm is deactivated. (10) MAIN MON: Alarm reaction on MAIN monitor in case of alarm. NO CHANGE: The currently selected main monitor display does not change. FULL SCREEN: Monitor displays the alarm camera (see (3)) image in full screen. (11) CALL MON: Alarm reaction on CALL monitor in case of alarm. NO CHANGE: The currently selected call monitor display does not change. ...
Эта инструкция также подходит к моделям:Видеонаблюдение - EDR-920 (2.93 mb)