Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Define the reaction upon video signal loss for each camera in this menu: (1) VLOSS: ENABLE: Video loss detection is activated. DISABLE: Video loss detection is deactivated. (2) DURATION: Alarm duration. Duration applies to buzzer and output contact and is adjustable from 1~99 seconds. (3) ALARM OUTPUT: Output relay activation. 1: Output relay 1 ~ 4 (selection) is switched in case of alarm NONE: Output relay is deactivated. (4) ALARM EMAIL: By selecting “ON”, an email is sent in case of alarm, containing the alarm message and the DVR IP address as sender. Define the email recipiant’s details in the NETWORK menu. (5) BUZZER: Alarm buzzer activation ENABLE: Alarm buzzer is activated. DISABLE: Alarm buzzer is deactivated. (6) ALARM NETWORK: Network alarm function activation. Network alarm reception requires installation of the optionally available PowerCon software. The network alarm transmits both the alarm message and the DVR IP address as sender to up to 3 recipiants. YES: Network alarm is activated. NO: Network alarm is deactivated. (10) SUMMARY: The SUMMARY menu item gives a summary on the settings for control purpose. Use the JOG to browse the individual settings. ATTENTION: This menu does not allow any editing of settings. 41 3.7 NETWORK MENU Define all network-related settings in this menu. These settings should only be carried out by skilled personnel qualified for network installation; if the DVR is implemented in existing networks, the network administrator should be consulted. This chapter doesn‘t go into basic network technique details. For further information, especially about router installation and internet connection, please refer to the publication "EverFocus network technique". 3.7.1 NETWORK NETWORK SETUP MENU CONFIG DHCP NO ALARM IP ADDRESS 192.168.001.200 EMAIL SUBNET MASK 255.255.255.0 PASSWORD GATEWAY 192.168.001.100 DNS SERVER 192.168.001.110 HTTP PORT 00080 CONTROL PORT 01600 DATA PORT 37260 MAC ADDR 00:11:14:01:83:2A Define the basic DVR TCP/IP settings in the NETWORK menu: (1) DHCP: DHCP ( Dynamic Host Communication Protocol), automatic IP number assignment (if supported by the network). YES: DHCP activated NO: DHCP deactivated. (2) IP ADDRESS: Enter the DVR’s IP address. If DHCP is activated, IP address is assigned automatically. (3) SUBNET MASK: Local network subnet mask: If DHCP is activated, subnet mask is assigned automatically. (4) GATEWAY: Network gateway IP address for external access. If DHCP is activated, gateway address is assigned automatically. (5) DNS SERVER: Local network DNS server IP address. If DHCP is activated, DNS server address is assigned automatically. 42 (6) HTTP PORT: Default setting for this port is: 80. The port can be changed if necessary. (7) CONTROL PORT: Default setting for this port is: 1600. The port can be changed if necessary. (8) DATA PORT: Default setting for this port is: 37260. The port can be changed if necessary. ATTENTION: If several users simultaneously access the DVR via network, each user requires a DATA PORT (max. 4 users). Upon activating ports, e.g. in firewalls, the following ports have to be opened additionally: DATA PORT +1 DATA PORT +2 DATA PORT +3 Example: Dataport 37260 > ports to be opened : 37260, 37261, 37262, 37263 (9) MAC ADDR: Display of network interface MAC address (cannot be changed). 3.7.2 ALARM (Network alarm) NETWORK SETUP MENU CONFIG PROTOCOL UDP ALARM PORT NUMBER 01600 EMAIL UNIQUE ID _ _ _ _ _ _ _ _ _ PASSWORD SERVER1 192.168.001.122 SERVER2 192.168.001.123 SERVER3 192.168.001.124 Having installed the optionally available PowerCon software, the DVR can transmit a network alarm to up to 3 recipiants in case of event. (1) PROTOCOL: Network alarm transmission protocol type TCP: TCP protocol transmission UDP: UDP protocol transmission (2) PORT : Network port through which the alarm is transmitted. This port must be set at the client’s side (recipiant) correspondingly. (3) UNIQUE ID: DVR ID number, used for identification by the recipiant’s software. 43 (4) SERVER 1 : Alarm server 1 IP address (recipiant) (5) SERVER 2 : Alarm server 2 IP address (recipiant) (6) SERVER 3 : Alarm server 3 IP address (recipiant) 3.7.3 EMAIL (Email alarm) NETWORK SETUP MENU CONFIG ALARM EMAIL PASSWORD SMTP SERVER PORT NUMBER AUTHENTICATION_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 00025 NO USER _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ PASSW. EMAIL ADR _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Define the recipiant’s email account settings for email alarm in the EMAIL menu item. Email alarms can be sent upon motion, alarm contact and technical alarms (WARNING menu). An *.arv file format alarm image is transmitted upon motion and alarm contact alarms. The visibility of these images requires installation of the EDR viewer software on the recipiant’s PC. The software may either be copied to USB stick in the COPY me...
Эта инструкция также подходит к моделям:Видеонаблюдение - EDR-1640 (2.93 mb)