Оценок - 3, средний балл: 3.7 ( )

Производитель: Panasonic Размер: 3.04 mb Название файла: WJSX550B.PDF Язык инструкции:

Refer to the Board Setting on page 39, (3) Test Button (TEST) This button is used to run the alarm test mode in combination with the Mode Selection Switch. TE ST Q- RESET o- A w 33 64 w <3) -© 100 msec. n r OV K- t -si Normally Closed (NOR CLOSE) (Close) Alarm Sensor (Open) Alarm Sensor O-cr^^o-o t> 100 msec. \*~ t ~*\ OV- - 1-32 Pin No. Designation Pin No. Designation Board No. 1 Board No.2 Board No.1 Board No.2 1 Alarm 1 Alarm 65 20 Alarm 20 Alarm 84 2 Alarm 2 Alarm 66 21 Alarm 21 Alarm 85 3 Alarm 3 Alarm 67 22 Alarm 22 Alarm 86 4 Alarm 4 Alarm 68 23 Alarm 23 Alarm 87 5 Alarm 5 Alarm 69 24 Alarm 24 Alarm 88 6 Alarm 6 Alarm 70 25 Alarm 25 Alarm 89 7 Alarm 7 Alarm 71 26 Alarm 26 Alarm 90 8 Alarm 8 Alarm 72 27 Alarm 27 Alarm 91 9 Alarm 9 Alarm 73 28 Alarm 28 Alarm 92 10 Alarm 10 Alarm 74 29 Alarm 29 Alarm 93 11 Alarm 11 Alarm 75 30 Alarm 30 Alarm 94 12 Alarm 12 Alarm 76 31 Alarm 31 Alarm 95 13 Alarm 13 Alarm 77 32 Alarm 32 Alarm 96 14 Alarm 14 Alarm78 33 Not used Not used 15 Alarm 15 Alarm 79 34 Not used Not used 16 Alarm 16 Alarm 80 35 Not used Not used 17 Alarm 17 Alarm 81 36 Ground Ground 18 Alarm 18 Alarm 82 37 Ground Ground 19 Alarm 19 Alarm 83 33*64 Pin No. Designation Pin No. Designation Board No.1 Board No.2 Board No.1 Board No.2 1 Alarm 33 Alarm 97 20 Alarm 52 Alarm 116 2 Alarm 34 Alarm 98 21 Alarm 53 Alarm 117 3 Alarm 35 Alarm 99 22 Alarm 54 Alarm 118 4 Alarm 36 Alarm 100 23 Alarm 55 Alarm 119 5 Alarm 37 Alarm 101 24 Alarm 56 Alarm 120 6 Alarm 38 Alarm 102 25 Alarm 57 Alarm 121 7 Alarm 39 Alarm 103 26 Alarm 58 Alarm 122 8 Alarm 40 Alarm 104 27 Alarm 59 Alarm 123 9 Alarm 41 Alarm 105 28 Alarm 60 Alarm 124 10 Alarm 42 Alarm 106 29 Alarm 61 Alarm 125 11 Alarm 43 Alarm 107 30 Alarm 62 Alarm 126 12 Alarm 44 Alarm 108 31 Alarm 63 Alarm 127 13 Alarm 45 Alarm 109 32 Alarm 64 Alarm 128 14 Alarm 46 Alarm 110 33 Not used Not used 15 Alarm 47 Alarm 111 34 Not used Not used 16 Alarm 48 Alarm 112 35 Not used Not used 17 Alarm 49 Alarm 113 36 Ground Ground 18 Alarm 50 Alarm 114 37 Ground Ground 19 Alarm 51 Alarm 115 ■ Board Setting Before installing this board, the following settings should be made by qualified service personnel or system installers. 1. Set switches (SW1) on the board to designate the Alarm Input board number as shown below. SE- ED* SW1 UNIT ADR D> SW1 UNIT ADR ÏÜ3 D> □» Û« 0« □« □i 0* □i □i 2. Set switches (SW4, SW5, SW6, SW7, SW8, SW9, SW10 and SW11) on the board to meet the alarm input requirements. NOR OPEN: Normally Open Input NOR CLOSE: Normally Closed Input The factory default setting is Normally Open (NOR OPEN). NOR CLOSE NOR OPEN SW4 “1-2—3—4—5—B-7—5“ BBBBBBBB OFF _ CVJ "2—3—* SW5 r BBBBBBBB OFF Switch No. Alarm Input Board No.1 Board No.2 1 SW4 1 -8 65-72 2 SW5 9-16 73-80 3 SW6 17-24 81-88 4 SW7 25-32 89-96 5 SW8 33-40 97-104 6 SW9 41 - 48 105-112 7 SW10 49-56 113-120 8 SW11 57-64 121-128 3. Confirm that switches (SW12) on the board are set as follows. §E> E> SW12 --------------------Note------------------------- These switches are used only for factory test. Always keep these switches in the “OFF" positions in the field. WV-PB5548 Data Board ■ Appearance © Data Connector (TA/TB/RA/RB/G, 1 - 8) These connectors are used to exchange control data with the camera site equipment. For connection, use a data grade shielded 4-wire twisted pair cable suitable for RS-485 communication. Cable length may be extended up to 1 200 m (4 000 ft). RT: Termination Resistor, 150 f2 1/2 W SW: Selection Switch, Full Duplex/Half Duplex GND: Ground; connected to each channel and common ground. f— DATA (RS485)® A T © © A R © 1 © Ù T © © A © * © © T © © A © © © A T 6 © © A © 4 B © G P A ; © © R © © A T © © © © © A 7 © © A R © © A T e © © A © nB © G ©

Скачать инструкцию

Чтобы скачать, введите 2 цифры: