Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Water “sheets” off dishes rather than forming waterdroplets that cling and leave spots. A dispenser, located next to the detergent cup, automatically releases a measured amount ofrinse aid during the last rinse. If spotting andpoor drying are problems, increase theamount of rinse aid dispensed by rotating thedial to a higher number. The dial is located under the dispenser cap. The indicator will bedark when full and will show clear when it is time to refill. To add liquid rinse aid, turn dispenser cap 1/4turn counterclockwise and lift out. Pour in rinse aid until liquid touches the indicated fill level. Replace cap. Do not overfill since this can cause oversudsing. Wipe up any spills with a dampcloth. The dispenser holds enough for 35 to 140washes, depending on setting. Factors Affecting Factors AffectingFactors AffectingFactors AffectingFactors AffectingFactors AffectingPerformance PerformancePerformancePerformancePerformancePerformance W WWWWWater T ater Tater Tater Tater Tater Temperatur emperaturemperaturemperaturemperaturemperature eeeee Hot water is needed for best dishwashing and drying results. Water entering dishwasher should be 120°F to give satisfactory results. Improved performance may be obtained by raising water temperature to 140°F. Water temperature should not exceed 160°F. Check your water heater for proper temperature. To check water temperature entering dishwasher, turn on hot water faucet nearest dishwasher for several minutes to clear cool water from water pipes. Place a glass under faucet and use a candy or meat thermometer to check temperature of the water collected. If temperature is below 120°F (49°C), have a qualified person raise the hot water heater thermostat setting. Do not operate the dishwasher during or just after other heavy use of hot water, such as laundry or bathing. Important: Before starting a cycle, run hot water through faucet to clear cool water from pipe. ENGLISH ENGLISHENGLISHENGLISHENGLISHENGLISH Adjustable setting Dispenser Opening Indicator MoreLess Dispenser Cap 10 Car CarCarCarCarCare and Cleaning e and Cleaninge and Cleaninge and Cleaninge and Cleaninge and Cleaning Burn Hazard Allow heating element to cool before cleaning the interior. Failure to do so can result in burns. Outside OutsideOutsideOutsideOutsideOutside—Occasionally wash with a mild nonabrasive detergent and water. Rinse and dry. Inside InsideInsideInsideInsideInside—The inside of the dishwasher is self- cleaning with normal use. To clean Stainless Steel wipe with the grains. Use a Dishwasher Safe Detergent to help with the stains or discolorations. Never use products that contain Chlorine Bleach or Citric Acid Important: The dishwasher motor is permanently lubricated at the factory and does not need to be oiled. Car CarCarCarCarCare of Drain Air Gap e of Drain Air Gape of Drain Air Gape of Drain Air Gape of Drain Air Gape of Drain Air Gap If a drain air gap was installed for your built-in dishwasher, check to make sure it is clean so the dishwasher will drain properly. Drain air gaps are usually mounted on countertop and can be inspected by removing the cover. A drain air gap is not part of your dishwasher and is not covered by this warranty. Winterizing WinterizingWinterizingWinterizingWinterizingWinterizing A dishwasher left in an unheated place should be protected from freezing. Have a qualified person do the following: T TTTTTo Disconnect Ser o Disconnect Sero Disconnect Sero Disconnect Sero Disconnect Sero Disconnect Service: vice:vice:vice:vice:vice: 1. Turn off electrical power to the dishwasher at the supply source by removing fuses or tripping circuit breaker. 2. Shut off water supply. 3. Place a pan under the inlet valve. Disconnect water line from inlet valve and drain into pan. 4. Disconnect drain line from pump and drain water into pan. Note: See Installation Instructions for more details. T TTTTTo Restor o Restoro Restoro Restoro Restoro Restore Ser e Sere Sere Sere Sere Service: vice:vice:vice:vice:vice: 1. Reconnect the water, drain, and electrical power supply. 2. Turn on water and electrical power supply. 3. Fill both detergent cups and run dishwasher through a NORMAL WASH Cycle. 4. Check connections to make sure they do not leak. Note: See Installation Instructions for more details. ENGLISH ENGLISHENGLISHENGLISHENGLISHENGLISH 11 Car CarCarCarCarCare and Cleaning e and Cleaninge and Cleaninge and Cleaninge and Cleaninge and Cleaning continued Property Damage Hazard Freezing temperatures may cause waterlines to rupture. Be sure all supply lines toand circulating lines within dishwasher areprotected. Failure to do so could result in propertydamage. Cleaning the Spray Arm Cleaning the Spray ArmCleaning the Spray ArmCleaning the Spray ArmCleaning the Spray ArmCleaning the Spray Arm The spray arm may need to be cleaned to insure that there are no clogs to the spray arm jets and bearings due to hard water chemicals. To remove spray arm simply hold the spray arm in place and turn th...
Эта инструкция также подходит к моделям:Посудомоечные машины - 587.144 (2.21 mb)