These conditions can cause fire or electric shock. Confirm that smoke has stopped and contact an authorized service center. For best performance • If a power failure occurs, the unit will not function. Introduction and Installation Included items • The Mounting base comes preattached to the Door station. No. Item Quantity Notes Door station 1 -----Mounting base 1 -----Wood screws 2 4 mm x 20 mm (3/16 . x 13/16 . ) Button cover 1 ----- Introduction and Installation Location of controls Front view Camera • When a visitor presses the Call Button, the camera will turn on and an image of the visitor will be shown on the display of the monitor station and sub monitor station. • The camera angle can be adjusted when installing the door station (page 9). Infrared light Microphone Speaker Call Button* • A visitor can press this button to call the monitor station and sub monitor station. Position indicator (Green) • The Position indicator is lighted with a green LED light while the power is on. Water drain holes (4 places) • These holes allow rainwater to drain away. Do not cover them. * Be sure to attach the accessory button cover to the Call Button before using it. (The diagram shows the button cover installed.) (Page 11.) Introduction and Installation Before installation To avoid malfunction or communication disturbance, do not install the door station in the following locations: – Places where vibration or any other kind of impact occurs. – Places where echoing is frequent. – Places where a high concentration of dust, hydrogen sulfide, phosphorus, ammonia, sulfur, carbon, acid, or noxious fumes occur. – Within 2 m (6.7.) of a TV, microwave, personal computer, air conditioner or any other electrical device. Note: • Be sure to install the monitor station and sub monitor station more than 5 m (16.5.) away from the door station. Introduction and Installation Installing the door station 1 Loosen the mounting screw, and then remove the mounting base. Screwdriver 2 Install the mounting base to a wall using the attached wood screws. (4 mm x 20 mm, 3/16 . x 13/16 .). Mounting base Wall Wood Screws Note: •Install so that picture range will be within a height of 995 mm ~ 1795 mm from the ground surface. Important information: On the bottom surface of the door station, there are holes to allow water to drain. Do not cover it up when installing. Introduction and Installation 3 Remove the adjustment cover, and then adjust the angle of the camera lens. Screwdriver Left direction (maximum 16°) Angle adjustment lever Right direction (maximum 16°) Upward direction (maximum 16°) Adjustment cover * Be sure to install the adjustment cover after adjusting the angle of the camera lens. Standard installation height and filming range Adjust the angle of the camera lens when carrying out installation. • Vertical direction (facing the front) (16° to the right)(16° upward) • Horizontal direction (facing the front) •The angle can also be adjusted 16° to the left. Note: • The measurements and angles are for reference purposes and may vary depending on the environment. • If a strong light is against the door station, the visitor’s face may not be distinguishable. Do not place the door station in the following locations. – Where most of the background is the sky. – Where the background is a white wall, and direct sunlight will reflect off it. – Where direct sunlight will shine on the door station. – Depending on where this unit is installed, surrounding noises will cause howling (beeping sound) to occur. Please avoid installing the unit in such a place. • Make sure the back of the door station is not subject to water. Wire type and distance • Wire (between the monitor station and the door station): Type: General cable CAT-3 24 AWG. Distance: Maximum 100 m (about 328 feet). Introduction and Installation 4 Attach the wire to the terminal. Wire (Not included) Tighten with screws Mounting base Door station Speaker Microphone 5 Secure the door station to the mounting base. Connect to terminals D11 and D12 (D21 and D22) of the monitor station. Wall Wall Door station (rear) Screwdriver • Tighten the mounting screws. Introduction and Installation 6 Attach the button cover. • Align the inside of the button cover base with the bottom of the call button, and then push the top of the button cover to fit it into place. Button cover Button cover Align with base. Push Call button Removing the button cover •Insert a flat-tipped screwdriver as far as it will go into the slot in the base of the button cover, and then turn the flat-tipped screwdriver to remove the button cover. * Press against the button cover gently with a finger when removing it, to stop it from falling down. Remove the button cover. Insert into the slot.1 Slots Screwdriver Screwdriver 2 Slot Help Cleaning Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit with a slightly damp cloth. Important info...
)
