Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Using the Flash Feature The “F” button is used to disconnect a call and re-establish dial tone or to switch over to another caller if you use calling services such as Call Waiting or Three Way Calling. Please contact your local telephone company for information on these services. 1. During a call press the “F” button to access the flash feature. Using The Pause Feature For Dialing The “R/P” button is used to insert a temporary pause during a dialing sequence. Programming in a pause will cause the phone to wait two (2) seconds before dialing additional numbers. This feature may be used when it is necessary to dial an access code (9, for example) and wait for a second dial tone before you can dial an outside number. Press the “R/P” button at the required point during the memory storage process to program a pause. When dialing an international number for example (i.e. 011-555-55-555-5555), some telephone company systems will not register the entire number entry without a pause between the prefix numbers. You may have to dial 011- “R/P” button, dial 555- “R/P” button. This allows adequate timing for the phone number to register with the telephone company’s system and complete the call. Using Line Transfer Feature If extra handsets are set to the base unit: 1. During a phone conversation, press the “SEL” button and the handset number you wish to transfer to. The line will be on HOLD and will make an audio sound on the other handset. 2. On the other handset you can press to answer the call automatically after receiving the transfer ring. 3. Press the button to return the connection back if the other handset user does not want to take the call during the transfer ring. 4. If the two handsets do not respond within 60 seconds, the line will disconnect automatically. Using The Page / Handset Location Feature Send a page signal from the base to the handset or to locate the handset. 1. Press the /PAGE button located on the base of the telephone to page the handset. 2. Press the /PAGE button once more to cancel the paging feature. 3. If you do not press the /PAGE button again, the handset will ring for about 30 seconds then end the paging automatically. Using The Headset Feature You can use this telephone hands-free when you connect a 2.5mm headset (purchased separately). To connect, plug the headset into the HEADSET JACK at the bottom of the handset. While in the Headset Mode, the volume of the headset is controlled by the telephone and the handset’s earpiece and microphone are disconnected. Follow the procedures discussed in ANSWERING A CALL and PLACING A CALL (See pages #17 & 18) when you receive and place a call. NOTE: When you plug the headset into the HEADSET JACK, it automatically mutes the microphone and speaker of the cordless handset. Unplug the headset to return the handset to normal use. Ordering a Headset or Neckloop: Headsets are available at most retail outlets that sell telephone equipment or contact BellSouth Special Needs Equipment Center at 800- 586-9828 or visit We recommend using the BellSouth Headset or BellSouth CLA7 Amplified Powered Neckloop. Phone Book Operation Storing Name And Numbers To Phone Book You can store up to 60 names and numbers in the memory. Dialing a number from phone book 1. In standby mode, press the “MEMO” button, and then the LCD shows the total number of records. 2. Press the or arrow button to go to the record you want to dial. Please see REVIEWING NAMES & NUMBERS IN THE PHONE BOOK (on page #20) for other modes of selection. 3. When the screen displays the number you want to dial, press the # symbol. The phone automatically dials the number. VIP and REJECT Functions If you store a name ending with “*” key, it will be a VIP (Very Important Person) number. If you store a name ending with key, it will be a REJECT number. When a VIP number is received, the handset ringer will operate (ring) whether or not it is turned ON or OFF. When a REJECT number is received, the handset ringer will not operate (ring) whether or not the feature is turned ON or OFF. Adding numbers and names to phone book 1. Begin with the phone in the standby mode, add the new number you want to store using the keypad. Enter the phone number up to 23 digits. 2. Press the “MEMO” button and then the LCD will show NAME. 3. Enter the name up to 11 characters using the “2 to 9” on keypad. Press the 2 key once for A, twice for B and 3X for C. Press the number “1” key to insert a space between name. Press the “F” button to erase any mistake. 4. Press the “MEMO” button to confirm and a confirmation beep will sound. -Or- Save numbers and names from the CALLER ID to phone book 1. Begin with the phone in the standby mode, press the or arrow button repeatedly to find the CALLER ID number you want to add. 2. If the number has the caller’s name, press the “MEMO” button to store. If the number does not have the caller’s name, press the “MEMO” button and then enter the name. 3. When completed, ...
Эта инструкция также подходит к моделям:Радиотелефоны - A50 (815.17 kb)