Оценок - 2, средний балл: 3.5 ( )

Производитель: EverFocus Размер: 3.23 mb Название файла: Язык инструкции:

Auto Logoff: Check this box to automatically logoff the current user after 3 minutes of inactivity. 77 There are three system access levels. The following charts show the rights of each level. Main Menu at the DVR User Level and Right RIGHT ADMINISTRATOR MANAGER OPERATOR Playback OK OK NO PTZ OK OK NO Layout OK OK OK Channel OK OK OK Display OK OK OK Sequence OK OK OK Monitor OK OK OK Zoom OK OK NO Search OK OK NO Copy OK OK NO Config. OK OK OK Logout OK OK OK Configuration Menu at the DVR User Level and Right RIGHT ADMINISTRATOR MANAGER OPERATOR Express OK NO NO Camera OK NO NO Record/Play OK NO NO Alarm/Event OK NO NO Schedule OK NO NO Network OK NO NO Disk OK NO NO Display OK OK NO System OK (1) (2) Info OK OK Ok (1) Only USER submenu; only access to change own password, and to access operator ID’s (2) Only USER submenu; only ability to change own password. 78 79 4.9.4 I/O Control Figure 4-35 is a screen shot of the I/O Control Setting Menu. This menu is used to define the settings for controlling the DVR through RS485, and for DVR control of attached PTZ cameras. Figure 4-35 System Menu – I/O Control RS485 PTZ Protocol: Select PTZ protocol, choose from the following protocols: Transparent, Pelco D, Pelco P, Everfocus, or Samsung. (NOTE: all cameras must use the same protocol) 485 ID: This is the ID used by the EKB500 to send commands to the DVR. On an RS485 connection, every device (PTZ, DVR and controller) must be assigned a unique ID number between 0 and 127. Baud Rate: The speed used to transmit instructions or information through the RS485 port on the DVR. Choose from the following speeds: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 BPS. Data Bit: The number of data bits used in a data packet or word. This can be set to 8 or 7. Stop Bit: This field is to set the number of stop bits indicating the end of a data packet. This can be set to 1 or 2. Parity: This selects the transmission error checking rule. Choose either None, Odd, or Even. Control One remote control can be used to operate several DVRs. The DVR to be addressed is selected by pressing the key corresponding to its ID number on the remote control. IR Remote ID: ID used by the remote control to select this DVR. This can be set from 1 to 4. 4.9.5 Misc. Figure 4-36 System Menu – Firmware & Misc. Firmware Current Firmware Version: Displays the current version. Firmware Upgrade: Press “Upgrade” to upgrade the firmware. NOTE: To perform a Firmware Upgrade, you will need to connect a USB flash device with the latest version of the firmware. Do not disconnect the USB device or turn off the power to the unit during the upgrade; this can cause the system to fail to recover, requiring factory service to repair. Configurations Load Factory Default: Click “Load” to restore all menu settings to the default values. User Account, Network Setting, and Time are not affected. Load From USB: Click “Load” to upload saved DVR configuration settings from a USB flash device. Save To USB: Click “’Save” to save the current DVR configuration settings to a USB flash device. Language: Choose which language the DVR uses. The available languages may vary based on region. 80 4.10 INFORMATION 4.37 is a screen shot of the INFORMATION MENU. This menu displays important system information. Figure 4-37 Information Menu – System 4.10.1 System System Version: Displays firmware version number. Model: Displays DVR model number. NTSC/PAL: Displays current video format. Network IP: Displays the DVR’s current IP Address. MAC: Unique address of the DVR’s internal network card. This option cannot be changed. DVR Name: Displays DVR DDNS name Network ID: The ID number for the PowerCon alarm network. Status Disk: Displays disk status; normal disk operation is indicated by “OK”. 81 4.10.2 Log Figure 4-38 Information Menu – Log From Date: Select starting date of log to be displayed. Time: Select starting time of log to be displayed. To Date: Select end date of log to be displayed. Time: Select end time of log to be displayed. Log Type: Configurations: to see log entries related to configuration changes. Event: to see log entries related to events. Record: to see log entries related to recording changes. Operation: to see log entries related to operation changes. User: to see log entries related to user access. View Log: Press “View Log” button to view the log. See Figure 4-39 for more detail. Clear Log: Press “Clear Log” button to clear the log. Export Log to USB: Press “Export’ button to export log data to USB. 82 Figure 4-39 Log List Prev Page: Go to the previous page of log. Next Page: Go to the next page of log. Close: Close the window 83 Chapter 5 5 Networking Overview This chapter will give you a basic instruction on how to set up the DVR for network connection. It is highly recommended that you have a working knowledge of what a network is and how it works. This will be helpful in completing the networking process. 5.1 Introduction to TCP/IP TCP/IP is the group of protocols u...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: