Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined byturning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures: • Re-orient the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/television technician for help. The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4. IMPORTANT INFORMATION This equipment complies with Part 68 of the FCC Rules and, if the product was approved July 23, 2001 or later, the requirements adopted by the ACTA. On the side of this equipment is a label that contains, among other information, a product identifier. If requested, this number must be provided to the Telephone Company. Product Identifier: US:F53AL01B9047 USOC Jack: RJ-31X Telephone Connection Requirements A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed tobe connected to a compatible modular jack that is also compliant. Seeinstallation instructions for details. Ringer Equivalence Number (REN) The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local Telephone Company. For products approved after July 23, 2001, the REN for this product is partof the product identifier that has the format US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. REN = 0.1B Incidence of Harm If this equipment (SCW9047/SCW9045) causes harm to the telephonenetwork, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isnot practical, the Telephone Company will notify the customer as soon aspossible. Also, you will be advised of your right to file a complaint withthe FCC if you believe it is necessary. Changes in Telephone Company Equipment or Facilities The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the Telephone Company will provide advance notice inorder for you to make necessary modifications to maintain uninterrupted service. New Zealand - Equipment Maintenance Facility If trouble is experienced with this equipment (SCW9047/SCW9045) forrepair or warranty information, contact the facility indicated below. If theequipment is causing harm to the telephone network, the TelephoneCompany may request that you disconnect the equipment until the problem is solved. This equipment is of a type that is not intended to be repaired by the end user. DSC c/o APL Logistics 757 Douglas Hill Rd., Lithia Springs, GA 30122 Additional Information Connection to party line service is subject to state tariffs. Contact the statepublic utility commission, public service commission or corporationcommission for information. Alarm dialling equipment must be able to seize the telephone line andplace a call in an emergency situation. It must be able to do this even ifother equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialling equipmentmust be connected to a properly installed RJ-31X jack that is electricallyin series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the figure below. If you haveany questions...
Эта инструкция также подходит к моделям:Видеонаблюдение - PowerSeries SCW9047-433 (506.74 kb)