Оценок - 4, средний балл: 3
(
)
)
|
Фрагмент инструкции
2. Select one option among PAL I/PAL G/PAL B using the button, and press the OK button. 3. UHF Offset You can adjust fine tuning setting. 1. Select UHF Offset using the button, and press the OK or button. 2. Select a range between -4~+4 using the button, and press the OK button. GB 57 9. Setting Preferences 9.6 Miscellaneous Settings 1. Press the MENU button. 2. Select Preferences using the button, and press the OK or button. 3. Select Miscellaneous Settings using the button, and press the OK or button. 1. i-Plate Display Time You can set the duration during which the Information box is to be displayed when you switch the channel. 1. Select i-Plate Display Time using the button, and press the OK or button. 2. Select a value between 1~20 seconds using the button, and press the OK button. Note: When it is set to Disable, the i-Plate will not be displayed when you switch the channel. 2. OSD Transparency You can set the transparency of On Screen Display (OSD). 1. Select OSD Transparency using the button, and press the OK or button. 2. Select one option among Disable/25/50/75 using the button, and press the OK button. Disable Fully opaque screen 25, 50, 75 As the number is bigger, the screen is more transparent. 3. Option in CH List You can set whether or not to display the scrambled icon in channel list. 1. Select Option in CH List using the button. 2. Select one option from On/Off using the or OK button. On Scramble icon displays in the channel list. Off Scramble icon disappears in the channel list. GB 58 10. Installation This chapter describes how to search for channels and a series of procedures. 10.1 Automatic Search If your receiver is connected to the aerial and television, you can automatically search channels without entering any other information. 1. Select MENU button. 2. Select Installation using the button, and press the OK or button. 3. Enter Password using the NUMERICAL (0~9) buttons. 4. Select Automatic Search from Installation menu using the button, and press the OK or button. 5. Receiver starts to search channels automatically. Search Wait while the receiver searches for the channels, this may take a few minutes. 1. During operating search, the cursor is located at Stop. Therefore, if you press the OK button during searching, the operation is stopped and the channels found until then will be displayed. 2. If search operation is successfully completed, and the channel does not exist, press the OK button and try to reset the search operation again if necessary. 3. You can delete unnecessary channels from the searched channels. Select your desired channels to delete and press the OK button. Then select Delete and press the OK button. To delete all channels, select Select All to select all channels, select Delete, and press the OK button. 4. When completing Channel Search and deleting unnecessary channels, select Save to save the changes. GB 59 10. Installation 10.2 Manual Search You can search channels manually by searching parameters, if you know the MUX information. 1. Channel Number Enter your desired frequency channel to search. When entering frequency channel value, the appropriate frequency value is entered. 1. Select Channel using the button, and press the OK or button. 2. Select one of channel using the button, and press the OK button. 2. Frequency Enter the your desired frequency to search directly. When entering frequency, the appropriate channel for the entered frequency is automatically displayed on Channel. 1. Select Frequency using the button, and press the OK or button. 2. Enter frequency using the NUMERICAL (0-9) button and press the OK button. 3. Network Search If specified frequency channel information and other channel information are provided together, the channel, which belongs to other frequency channel, is also searched. 1. Select Network Search using the button, and press the OK or button. 2. Select one option between Enable and Disable using the or OK button. GB 60 ** 10.3 Default Setting Default Setting restores the receiver to the default settings. Warning: Please note that once you perform Default Setting, all data such as Channel List, and User Configured data are deleted. To perform Factory Default: 1. Press the MENU button. 2. Select Installation using the button, and press the OK or button. 3. Enter Password using the NUMERICAL (0-9) button. 4. Select Default Setting using the button, and press the OK or button. 5. Select Yes and press the OK button to restore all setting to Factory Default. Select No and press the OK or BACK button to return to the previous menu. 6. Confirm again to start loading default setting. Enter Password using the NUMERICAL (0-9) button to perform restoring. 7. When completing the default setting, press the OK button to automatically run Installation Wizard. When default setting is completed, Installation Wizard is automatically displayed, which helps Channel Search. For detailed information about Installation Wizard, refer to 3. Installatio...