Оценок - 4, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Not doing so may result in leaks. • Avoid opening and closing the covers while on the beach or near water. Change memory cards and batteries in a dry place protected from sea breezes. Initial Preparations Remove the battery. ..Open the cover and press the battery lock in the direction of the arrow. ..The battery will pop up. Removing the Battery and Memory Card Remove the memory card. ..Push the memory card in until it clicks, and then slowly release it. ..The memory card will pop up. Setting the Date and Time A screen for setting the date and time is displayed the first time you turn the camera on. Be sure to specify the date and time, which is the basis for dates and times added to your images. Turn the camera on. • Press the ON/OFF button. • The [Date/Time] screen is displayed. Initial Preparations Set the date and time. • Press the qr buttons to choose an option. • Press the op buttons to specify the date and time. • When finished, press the m button. Set the local time zone. • Press the qr buttons to choose your local time zone. Finish the setup process. • Press the m button when finished. After a confirmation message, the setting screen is no longer displayed. • To turn off the camera, press the ON/OFF button. • Unless you set the date, time, and local time zone, the [Date/Time] screen will be displayed each time you turn the camera on. Specify the correct information. • To set daylight saving time (1 hour ahead), choose in step 2 and then choose by pressing the opbuttons. Initial Preparations Changing the Date and Time Adjust the date and time as follows. Access the camera menu. • Press the n button. Choose [Date/Time]. • Press the zoom buttons to choose the 3 tab. • Press the op buttons to choose [Date/ Time], and then press the m button. Change the date and time. • Follow step 2 on p. 20 to adjust the settings. • Press the n button to close the menu. • Date/time settings can be retained for about 3 weeks by the camera’s built-in date/time battery (backup battery) after the battery pack is removed. • The date/time battery will be charged in about 4 hours once you insert a charged battery or connect the camera to an AC adapter kit (sold separately, p. 169), even if the camera is left off. • Once the date/time battery is depleted, the [Date/Time] screen will be displayed when you turn the camera on. Follow the steps on p. 19 to set the date and time. • Automatic date and time updating is possible using GPS (p. 56). Initial Preparations Display Language The display language can be changed as needed. Enter Playback mode. • Press the 1 button. Access the setting screen. • Press and hold the m button, and then immediately press the n button. Set the display language. • Press the opqr buttons to choose a language, and then press the m button. • Once the display language has been set, the setting screen is no longer displayed. • The current time is displayed if you wait too long in step 2 after pressing the m button before you press the n button. In this case, press the m button to dismiss the time display and repeat step 2. • You can also change the display language by pressing the nbutton and choosing [Language ] on the 3 tab. Trying the Camera Out Still Images Movies Trying the Camera Out Still Images Movies Follow these instructions to turn the camera on, shoot still images or movies, and then view them. Shooting (Smart Auto) For fully automatic selection of the optimal settings for specific scenes, simply let the camera determine the subject and shooting conditions. Red Mark Make sure the covers are closed. • Make sure that both the memory card/battery cover lock and terminal cover lock return to the positions shown, with the red marks no longer visible. • If either cover is not fully closed, water may enter the camera when it gets wet, which may damage it. Turn the camera on. • Press the ON/OFF button. • The startup screen is displayed. Enter A mode. • Press the o button, press the op buttons to choose A, and then press the m button. • Icons representing the scene and image stabilization mode are displayed in the upper right of the screen. • Frames displayed around any subjects that are detected indicate that they are in focus. Trying the Camera Out AF Frames Compose the shot. • To zoom in and enlarge the subject, press the i(telephoto) zoom button, and to zoom away from the subject, press the j (wide angle) zoom button. Shoot. Shooting Still Images Focus. • Press the shutter button lightly, halfway down. The camera beeps twice after focusing, and AF frames are displayed to indicate image areas in focus. Shoot. • Press the shutter button all the way down. • As the camera shoots, a shutter sound is played, and in low-light conditions, the flash fires automatically. • Your shot remains displayed on the screen for about two seconds. • Even while the shot is displayed, you can take another shot by pressing the shutter button again. Elapsed Time Trying the Camera Out Shooting Movies Start shooting. • Press...