Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
If the problem still persists, disconnect all power sources (including the battery pack and the backup battery). This will reset all the camcorder’s settings. flashes on the screen. -Load a cassette ( 21). flashes on the screen. -Battery pack is exhausted. Replace or charge the battery pack ( 15). flashes on the screen. -Condensation is detected. Refer to Condensation ( 56). [REMOVE THE CASSETTE] appears on the screen. -Remove the cassette and reinsert it ( 21). Video noise appears on screen. -When using the camcorder in a room where a plasma TV is located, keep a distance between the camcorder and the plasma TV. Video noise appears on the TV screen. -When using the camcorder in a room where a TV is located, keep a distance between the compact power adapter and the power or antenna cables of the TV. The tape stops during record pause or playback pause. -To protect the tape and video heads, the camcorder will enter the stop mode ( ) if left in playback pause ( ) or record 50 • Additional Information pause ( ) mode for 4 minutes 30 seconds. To resume the operation press Start/Stop (when recording) or push the joystick ( ) toward / (during playback). Recording Image will not appear on the screen. -Set the camcorder to mode ( 23). [SET THE TIME ZONE, DATE AND TIME] appears on the screen. -Set the time zone, date and time ( 20). -Replace the backup lithium battery ( 17) and set the time zone, date and time. Pressing will not start recording. Start/Stop -Set the camcorder to mode ( 23). -Load a cassette ( 21). -Tape reached the end (“ END” appears on the screen). Rewind the tape or replace the cassette ( 21). -Cassette is protected ( flashes on the screen). Change the position of the protect switch ( 55). Camcorder will not focus. -Autofocus does not work on that subject. Focus manually ( 32). -If you are using the viewfinder, adjust it with the dioptric adjustment lever ( 23). -Lens is dirty. Clean the lens with a soft lens-cleaning cloth ( 56). Never use tissue paper to clean the lens. Sound is distorted. -When recording near loud sounds (such as fireworks or concerts), sound may become distorted. Viewfinder picture is blurred. -Adjust the viewfinder with the dioptric adjustment lever ( 23). Playback During playback there is video noise. -Video heads are dirty. Clean the video heads ( 2). Playback does not start. -Load a cassette ( 21). -Set the camcorder to mode ( 27). -Tape reached the end (“ END” appears on the screen). Rewind the tape ( 21). No sound from the built-in speaker. -Open the LCD panel. -Speaker volume is turned off. Adjust the volume with the [SPEAKER VOLUME] setting ( 27). Image will not appear on the TV screen. -Check again that the camcorder is properly connected to the TV ( 39). Tape is running, but image will not appear on the TV screen. -TV/VIDEO selector on the TV is not set to VIDEO. Set the selector to VIDEO ( 40). -Video heads are dirty. Clean the video heads ( 2). -You attempted to play back or dub a copyright protected tape ( 42). Stop playback/dubbing. Editing Cannot record with this camcorder video input from an external video device connected using a DV cable. -Wrong signal standard. Refer also to the instruction manual of the connected device. Additional Information • 51 List of Messages (in alphabetical order) CHANGE THE BATTERY PACK -Battery pack is exhausted. Replace or charge the battery pack ( 15). CHECK THE CASSETTE [INCORRECT TAPE SPECIFICATION] -You attempted to play back a tape recorded in HD (high definition) standard. CHECK THE INPUT -The DV cable is not correctly connected to the DV terminal ( 39), or the connected digital device is turned off. CONDENSATION HAS BEEN DETECTED -Condensation has been detected in the camcorder ( 56). CONDENSATION HAS BEEN DETECTED REMOVE THE CASSETTE -Condensation has been detected in the camcorder ( 56). Remove the cassette. COPYRIGHT PROTECTED DUBBING RESTRICTED -You attempted to dub a copyright protected tape ( 42). COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED -You attempted to play back a copyright protected tape ( 42). HEADS DIRTY, USE CLEANING CASSETTE -Video heads are dirty. Clean the video heads ( 2). INCORRECT TAPE SPECIFICATION PLAYBACK IS RESTRICTED -You attempted to play back a tape recorded in a different television system (PAL or SECAM) or in a recording standard not supported by this camcorder. INPUT SIGNAL NOT SUPPORTED -The digital device connected with the DV cable is incompatible with the camcorder. REMOVE THE CASSETTE -Camcorder stopped operating to protect the tape. Remove the cassette and reinsert it ( 21). SET THE TIME ZONE, DATE AND TIME -You have not set the time zone, date and time. This message appears each time you turn the power on until you set the time zone, date and time ( 20). TAPE END -Tape reached the end. Rewind the tape or replace the cassette. THE TAPE IS SET FOR ERASURE PREVENTION -Cassette is protected. Replace the cassette or change the position of the protect switch ( 55). 52 • Additional Informatio...