Оценок - 2, средний балл: 4
(
)
)
|
Фото и характеристики Canon ZR900 |
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Connecting to a TV or VCR AV Terminal Sound from the built-in speaker will be muted while the STV-250N Stereo Video Cable is connected to the camcorder. DV Terminal Check the type and orientation of the terminal and make sure you connect the DV cable properly. Open the LCD panel to access. 48 Connection Diagrams Turn off all the devices when making the connections and refer also to the instruction manual of the connected device. Terminal on the Terminal on the Connecting Cable Camcorder Connected Device 1 Output connection (signal flow ) to a TV or VCR with AV Terminals. VIDEO AUDIO R L STV-250N Stereo Video Cable (supplied) Yellow White Red 2 Output connection (signal flow ) to a high-definition TV with a DV (IEEE1394) terminal. Input connection (signal flow ) from a TV or other digital video source with a DV (IEEE1394) output. DV cable (commercially available) 4-pin 6-pin* * Be careful to correctly insert the 6-pin plug into the DV terminal. Inserting it in the wrong direction can result in damage to the camcorder. External Connections Playback on a TV Screen The quality of the playback picture will vary depending on the connected TV and the type of connection used. ( 21) POINTS TO CHECK Before making the connections, select the [TV TYPE] setting according to the TV set to which you will connect the camcorder ( 58). Connecting Connect the camcorder to the TV following one of the connection diagrams shown in Connection Diagrams ( 49). Playback 1 Turn on the camcorder and the connected TV or VCR. On a TV: Select as the video input the same terminal to which you connected the camcorder. On a VCR: Set the input selector to the external video input (usually labeled LINE IN). 2 Start the playback of the movies ( 33). NOTES • Turn off all the devices before starting the connections. • We recommend powering the camcorder using the compact power adapter. Copying your Recordings to an External Video Recorder You can copy your recordings by connecting the camcorder to a VCR or a digital video device. When recording to a digital video recorder using the DV terminal, you can copy recordings with virtually no generation loss in video and sound quality. ( 21) Connecting Connect the camcorder to a VCR or other analog device using connection type 1 , or to a DVD recorder or other digital recording device using connection type 2 , as shown in Connection Diagrams ( 49). Recording 1 This camcorder: Load the recorded cassette. 2 Connected device: Load a blank cassette or disc and set the device to record pause mode. 3 This camcorder: Locate the scene you wish to copy and pause the playback shortly before the scene. 4 This camcorder: Resume the movie playback. When using an analog connection you can include in the copy also the date/time of the original recording ( 36). 5 Connected device: Begin recording when the scene you wish to copy appears. Stop recording when copying is complete. 6 This camcorder: Stop playback. NOTES • We recommend powering the camcorder using the compact power adapter. • When recording to a VCR using an analog connection –connection type 1 ( 49)–, the quality of the edited tape will be lower than the original. • When recording to a digital video recorder using the DV terminal –connection type 2 ( 49)–: -If the picture does not appear, disconnect the DV cable and restore the connection after a short while or turn the camcorder off and then on again. -Proper operation cannot be guaranteed for all digital devices equipped with a DV terminal. If the operation does not work, use the AV terminal. Digital Video Dubbing You can input video from other digital video devices and record the input video on the tape in the camcorder. ( 21) Connecting Connect the camcorder to the video input source using the digital connection –connection type ( 2 49)– shown in Connection Diagrams. Dubbing FUNC. ( 22) 1 Load a blank tape in the camcorder and load the recorded (source) tape or disc in the connected device. 2 Set the camcorder in record pause mode. FUNC. REC PAUSE] [EXECUTE] 3 Connected device: Start the playback. In record pause mode and while recording you can check the picture on the camcorder’s screen. External Connections 4 When the scene you wish to record appears, push the joystick ( ) toward / to begin recording. Recording starts. 5 While recording, push the joystick ( ) toward / to record pause. In record pause mode, push the joystick ( ) toward / again to resume recording. 6 Push the joystick ( ) toward to stop recording. 7 Connected device: Stop the playback. IMPORTANT • Blank sections may be recorded as anomalous picture. • If the picture does not appear, disconnect the DV cable and restore the connection after a short while or turn the camcorder off and then on again. • You can only record video signals in DV standard (standard definition, SP or LP mode) from devices carrying the logo. Note that signals from identically shaped DV (IEEE1394) terminals may be in different video standards. NOTES We recommend ...
Эта инструкция также подходит к моделям:Видеокамеры - ZR930 (3.17 mb)