Оценок - 4, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
9) Mains lead (1) (p. 9) Handycam Station (1) (p. 9) (DCR-HC22E) Wireless Remote Commander (1) (p. 28) (DCR-HC19E/HC21E/HC22E) A button-type lithium battery is already installed. A/V connecting cable (1) (p. 30, 47) USB cable (1) (p. 53) (DCR-HC19E/HC21E/HC22E) • A USB cable is not supplied with the DCR-HC17E model. If necessary, buy a USB 2.0 cable (Type A to Type B-mini.). A Sony product is recommended. Shoulder Strap (1) (p. 84) (DCR-HC19E/HC21E/HC22E) Rechargeable battery pack NP-FP30 (1) (p. 9, 78) CD-ROM “Picture Package Ver.1.5” (1) (p. 53) 21-pin adaptor (1) (p. 30) (DCR-HC22E) For the models with the C€ mark printed on their bottom surfaces only. Shoe cover (1) Attached to the camcorder. Operating Guide (This manual) (1) 8 Step 2: Charging the battery pack You can charge the “InfoLITHIUM” battery pack (P series) (p. 78) after attaching it to your camcorder. For DCR-HC22E: Handycam DC IN jack Station ^DC plug iack Vi To the wall socket AC Adaptor For DCR-HC17E/HC19E/HC21E: POWER switch 1 Attach the battery pack by sliding it in the direction of the arrow until it clicks. 2 Slide the POWER switch up to OFF (CHG). (The default setting. 3 Connect the AC Adaptor to the DC IN jack on the Handycam Station for the DCR-HC22E or on your camcorder for the DCR-HC17E/HC19E/HC21E. For DCR-HC22E: With the ▲ mark facing up DC IN jack For DCR-HC17E/HC19E/HC21E: facing down Continued ^ 9 Getting Started 4 For DCR-HC22E: Connect the mains lead to the AC Adaptor and the wall socket. Insert the camcorder into the Handycam Station securely, all the way to the bottom. CHG (charge) lamp The CHG (charge) lamp lights up and charging starts. • When inserting the camcorder into the Handycam Station, close the DC IN jack cover. For DCR-HC17E/HC19E/HC21E: Connect the mains lead to the AC Adaptor and the wall socket. CHG (charge) lamp when the battery is fully charged. Disconnect the AC Adaptor from the DC IN jack. For DCR-HC22E: Disconnect the AC Adaptor from the DC IN jack holding both the Handycam Station and the DC plug. To remove the battery pack Turn off the power, then press PUSH button and remove the battery pack. PUSH button POWER switch When storing the battery pack Fully discharge the battery before storing it for an extended period (p. 79). For DCR-HC22E: To charge the battery pack using only the AC Adaptor Turn off the power, then connect the AC Adaptor to the DC IN jack on your camcorder. • You can operate your camcorder connected to a power source such as a wall socket as shown in the illustration. The battery pack will not lose its charge in this case. The CHG (charge) lamp lights up and charging starts. 5 The CHG (charge) lamp turns off 10 Charging time Approximate time (min.) required when you fully charge a fully discharged battery pack. Battery pack Charging time NP-FP30 (supplied) 115 NP-FP50 125 NP-FP70 155 NP-FP90 220 Recording time Approximate time (min.) available when you use a fully charged battery pack. For DCR-HC22E: To remove your camcorder from the Handycam Station Turn off the power, then remove the camcorder from the Handycam Station holding both your camcorder and the Handycam Station. For DCR-HC17E/HC19E/HC21E: To use an outside power source You can operate your camcorder using the power from the wall socket by making the same connections as you do when charging the battery pack. The battery pack will not lose its charge in this case. Battery pack Continuous recording time Typical recording time* NP-FP30 80 40 (supplied) 105 50 NP-FP50 115 55 150 75 NP-FP70 240 120 310 5 5 NP-FP90 435 215 550 275 • All times measured under the following conditions: Top: Recording with LCD screen. Bottom: Recording with viewfinder LCD panel closed. * Typical recording time shows the time when you repeat recording start/stop, turning the power on/off and zooming. Playing time Approximate time (min.) available when you use a fully charged battery pack. Battery pack LCD panel opened LCD panel closed NP-FP30 (supplied) 95 120 NP-FP50 135 170 NP-FP70 280 350 Continued ^ 11 Getting Started Battery pack LCD panel opened LCD panel closed NP-FP90 500 620 On the battery pack • Before changing the battery pack, slide the POWER switch up to OFF (CHG). • The CHG (charge) lamp flashes during charging, or the battery information (p. 23) will not be correctly displayed under the following conditions. - The battery pack is not attached correctly. - The battery pack is damaged. - The battery pack is fully discharged. (For Battery Info only.) • The power will not be supplied from the battery as long as the AC Adaptor is connected to the DC IN jack of your camcorder or the Handycam Station supplied with the DCR-HC22E, even when the mains lead is disconnected from the wall socket. On the charging/recording/playback time • The recording and playback time will be shorter when you use your camcorder in low temperatures. • The...
Эта инструкция также подходит к моделям:Видеокамеры - DCR-HC19E (3.19 mb)
Видеокамеры - DCR-HC21E (3.19 mb)
Видеокамеры - DCR-HC22E (3.19 mb)