Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
b Set RF Adaptor VCR/TV Selector to TV. c Turn TV ON and select channel. VCR/TV Selector VHF Connecting Cable To VHF Antenna Terminal CATV System Installer This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 28 Playing Back Recordings in a VCR Load Battery in PlayPak Remove Battery lid and insert AA battery. • Do not reverse polarity. • Replace battery when tape loading/ unloading takes longer than usual. Insert HISCj Cassette in PlayPak Load Detector 1 2 3 TurnKBSS cassette Tape Wheel in direction of arrow to take up any slack. Slide RELEASE to open cassette lid. Insert the IVNSLij cassette with the window up and on the left, then snap lid shut. * Do not obstruct cassette reel while loading. • Allow PlayPak Load Detector to fully retract before using in VHS VCR. Remove ÜU3CJ Cassette 1 2 Slide RELEASE and wait for lid to open. Push cassette out through hole in bottom of PlayPak with your finger. 29 Copying your Tapes (dubbing) Connections (supplied) Monitor with your TV • Turn TV on and tune to VCR channel (CH3 or CH4). • Set VCR/TV Selector on VCR to VCR. Before you begin... • Make Camcorder-VCR connections (see left). • Turn both units on. • Set VCR input signal to LINE. Please see VCR owner’s manual. • Set Camcorder POWER to VCR. 1 2 3 4 Insert a pre-recorded tape into Camcorder and a blank tape with record tab into VCR. Press PLAY on Camcorder, then press STILL at starting point. Press REC, then STILL/PAUSE on VCR. Press STILL on Camcorder and STILL/PAUSE on VCR again to start copying. Press STOP on both units to stop copying. Note: • Camcorder will only playback tapes recorded in SP or SLP mode. • Dubbing may reduce picture quality. r CAUTION:-- Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement. 30 Power Zoom / Backlight ¿Four-Speed Power Zoom Zoom in (close up) and out (wide angle) in one of four speeds ranging from slow (16 sec.) to fast (2 sec.). Before you begin... • Connect Camcorder to power source. • Set POWER to CAMERA. Zoom In (“T”) fv2VW Zoom Out (“W”) Zoom slowly: Lightly press “T" (telephoto) or “W" (wide angle) POWER ZOOM button. Zoom quickly: Apply more pressure to the button. Backlight Use when subject is darker than surroundings, in shadowed area, or in front of the light source. Before you begin... • Connect Camcorder to power source. • Set POWER to CAMERA. Press BACKLIGHT while recording to select the level of backlight compensation. In normal lighting, press BACKLIGHT repeatedly until no indicator displayed. EVF Indications ►Normal (no display) O First press (low) O Second press (medium) I . O Third press (high) LJ Fourth press 31 Focus Auto Focus Before you begin... • Connect Camcorder to power source. •Set POWER to CAMERA. MANUAL FOCUS Manual Focus Use Manual Focus (MF) when : • recording through glass. • lighting is poor. • subject is far away with objects in foreground. • subject has distinct horizontal lines. Camcorder automatically focuses on subject even during zooming. Auto Focus is on when “MF” is not displayed in EVF. Push MANUAL FOCUS to remove “MF” in EVF if necessary. • subject is not centered in Viewfinder. • subject has shiny surface. • subject is slanted. • subject is bright and flat, like a white wall. • subject has fast motion, like a golf swing. 13 1 Push MANUAL FOCUS so “MF’ (Manual Focus) appears in EVF. EVF Indication 2 3 4 r ■\ MF V ) Hold down “T” (telephoto) on POWER ZOOM to maximum zoom in. Turn MANUAL FOCUS until subject is in focus. • Back away from subject if necessary. Hold down “W” (wide angle) on POWER ZOOM as desired. • Refocus as needed when aiming at new scenes. Auto Focus functions up to 1/2 inch (12.7mm) from subject. Hold down “W” on POWER ZOOM to maximum wide angle. Bring Camcorder up close to the subject. 32 High Speed Shutter Improves Still or Slow Motion playback picture of high speed subjects (e.g. a tennis stroke), when viewed on Camcorder or 3 or 4 head VCR. Before you begin... • Connect Camcorder to power source. • Set POWER to CAMERA. • • Insert cassette with record tab (page 13). Auto Shutter In AUTO mode (no indication in EVF), shutter speed is auto-adjusted from 1/60 to 1/350 according to subject brightness. • AUTO mode is selected each time POWER is set to CAMERA. Manual Selection The faster the shutter speed, the more light is needed for proper picture and color quality. High Speed Shutter indication flashes if light is inadequate. Provide additional light. 1 2 Press HIGH SPEED SHUTTER while recording. Press repeatedly to change shutter...