Оценок - 3, средний балл: 3.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Concerning the remaining tape time indication on the screen .The remaining tape time is indicated in minutes. (When it reaches less than 3 minutes, the indication starts flashing.) .During a 15-second or shorter recording, the remaining tape time indication may not be displayed or the remaining tape time may not be displayed correctly. .In some cases, the remaining tape time indication may display remaining tape time that is 2 to 3 minutes shorter than the actual remaining tape time. . [POWER SAVE] [OFF]: When 5 minutes passes without any operation, the standby mode will be automatically set. In the standby mode, [;] blinks and it takes more time than usual to start recording after you press the recording start/stop button. [5 MINUTES]: When 5 minutes passes without any operation, the Camcorder automatically turns off to protect the tape or to prevent the battery from running down. When you want to use the Camcorder, turn it on again. .The Camcorder cannot be automatically turned off when you connect the USB connection cable or the DV cable with the Camcorder or when the Camcorder is in the PC mode. Recording still pictures ona card while recordingimage onto a tape You can record still pictures while recording image onto a tape. .Set to Tape Recording Mode. 1 Press the [PHOTO SHOT] button fully while recording image onto a tape. PHOTO SHOT .For the number of still pictures to be recorded on a card, refer to -78-. .When recording pictures onto a card, the recording start/stop button is disabled. LSQT0861 Record mode .You can select a picture quality for still pictures to be recorded. (-30-) .In tape recording mode, the size of pictures that can be recorded is [640]. .In order to record higher quality still pictures, you must use the card recording mode. .If the wide mode is used, you cannot record images onto the card. .The [PHOTO SHOT] button does not work if it is pressed halfway. Check the recording The last image recorded is played back for 2 to 3 seconds. After checking, the Camcorder will be set to a recording pause. .Set to Tape Recording Mode. 1 Press the joystick during the recording pause until the icon 1 appears. 2 Move the joystick down to select the recording check icon [ ]. 1 Blank searchfunction Searches for the last part of the image recorded (unused part of the tape). .Set to Tape Recording/Playback Mode. 1 Set [BASIC] or [ADVANCE] >> [BLANK SEARCH] >> [YES]. . Stopping a blank search midway through Move the joystick down. .If the cassette tape has no blank part, then the Camcorder will stop at the end of the tape. .The Camcorder stops at a point approx. 1 second before the end of the last image recorded. When you start recording at that point, the image can be recorded seamlessly from the last image. Recording still pictures onto a card (Photoshot) .Set to Card Recording Mode. PC 1 Press the [PHOTO SHOT] button halfway in order to adjust focusing. (For auto focusing only) .The iris/gain value is fixed and this Camcorder focuses on the subject automatically. PHOTO SHOT 1 2 1 Shutter chance mark ± (The white lamp flashes.): Focusing . (The green lamp lights up.): When in focus No mark: When focusing is unsuccessful .The shutter chance mark is indicated as follows when the [PHOTO SHOT] button is not pressed halfway. Please use it as a guide for recording. . (The green lamp lights up.): When in focus and a good picture can be recorded ± (White lamp lights up.): Almost in focus 2 Focus area 2 Press the [PHOTO SHOT] button fully. . To record still pictures clearly .When zooming in on the subject with a magnification of 4k to 10k or higher, it is difficult to reduce the slight shaking from holding the Camcorder by hand. We recommend decreasing the zoom magnification and approaching the subject when recording. .When recording still pictures, hold the Camcorder firmly with your hands and keep your arms stationary at your side so as not to shake the Camcorder. .You can record stable pictures without shaking by using a tripod and the remote control. LSQT0861 Record mode .For the number of still pictures to be recorded on a card, refer to -78-. .The sound cannot be recorded. .While data is being recorded on a card, do not operate the mode dial. .When the access lamp is lit, do not insert or remove a card. .Another product may degrade or not play back data recorded on this Camcorder. .If set [PICT. QUALITY] >> [ ], mosaic-pattern noise may appear on a playback image depending on the picture content. .When the [PICTURE SIZE] is set to other than [640], the mega pixel recording mode is set. .When the picture size setting is other than [640], the scene around the subject can be recorded wider than that in [640]. . On-screen display in the card recording mode 100 1) 2) 3) 1) Still picture size 2) Number of recordable still pictures (When no pictures can be recorded, the red light will flash.) 3) Quality of still pictures . Progressive Photoshot You can record still pictures with higher picture quality and f...