Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Then, enter correct numbers by pressing [PLAY] or [STOP]. • You may cancel the entire program by pressing [REW] during the program number flashes. 5 Press [EXIT/RESET] to exit. 6 Press [POWER] to return to timer stand-by mode. COUNTER MEMORY FUNCTION Use this feature to memorize the beginning of recording start point. 1) Press [COUNTER RESET] on the remote control to reset the counter. 2) Press [COUNTER MEMORY] on the remote control so that “M” appears on the TV screen. REC SP M0:00:00M0:00:00 3) Record the program. 4) After recording, press [STOP] then [REW]. • When “0:00:00” is reached, rewinding operation goes to stop. And you can view the recording program. • [COUNTER MEMORY] does not function if the Auto repeat mode is set to [ON]. In this case, set the Auto repeat mode to [OFF]. • To cancel the Counter memory mode, press [COUNTER MEMORY] so that “M” disappears from the TV screen. SPECIAL FEATURES COPYING A VIDEO TAPE AUTO REWIND You can make copies of video tapes made by friends or relatives for your enjoyment. Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR(this unit), the playing VCR (another source) and your TV using the following diagram. [Recording VCR] (not supplied) (this unit) (Use for monitoring) Audio/Video cables[TV set] ANT in Coaxial cable (supplied) VIDEO INOUT CH3 CH4 AUDIO OUT IN ANT [Playing VCR] (another source) IN OUT IN OUT AUDIO VIDEO When a tape has reached the end during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the VCR will eject the tape and turn itself to off. • The VCR will not rewind the tape automatically during timer recording or One Touch Recording. • When the Counter Memory is activated, the tape will rewind to the M0:00:00 and the VCR will go into the Stop mode. REAL TIME TAPE COUNTER • This shows the elapsed recording or playback time in hours, minutes, and seconds. (The displayed time will not change during blank portions on the tape.) • The indication will appear when the tape is rewound further than “0:00:00” on the tape counter. RECORDINGFUNCTION SPECIALFEATURES 1) Insert a pre-recorded tape into the playing VCR. 2) Insert a tape with its safety tab into the recording VCR. 3) Press [TAPE SPEED] on the recording VCR to select the desired recording speed (SP/SLP). 4) Select the “Line-in” position on the recording VCR. See page 3, under “Using AUDIO/VIDEO Input jacks”. 5) Press [REC/OTR] on the recording VCR. 6) Begin playback of the tape in the playing VCR. • For best results during dubbing, use the VCR’s front panel controls whenever possible. The remote control might affect the playing VCR’s operation. • Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended. • You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs in place of the playing VCR. TO MONITOR THE RECORDING 1) Turn on the TV and set the TV to channel 3 or 4. Now set the CH3/CH4 switch on the back of the VCR to match the channel selected on the TV. 2) Press [VCR/TV] on the recording VCR so that the VCR/TV indicator comes on. – 6– EN TROUBLESHOOTING GUIDE If you have followed the instructions contained in this manual and have difficulty in operating your VCR, locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to remedy the problem. PROBLEM CORRECTIVE ACTION No power. • Make sure the power plug is connected to an AC outlet. • Make sure the power is turned on. Timer recording is impossible. • Make sure the timer recording is set correctly. • Make sure the power is off. • Make sure the VCR clock is set correctly. Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape. Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing [CHANNEL ] on the VCR. ( ) Cannot view a tape but the audio is OK. • Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” . • Make sure the VCR is not in the Menu mode. No or poor playback picture. • Select channel 3 or 4 at your TV, then press [VCR/TV] so that the VCR/TV indicator on the VCR comes on. • Fine tune your TV. TV programs cannot be seen normally. • Re-check the ANT. IN and ANT. OUT connections. See page 3. • Press [VCR/TV] so that the VCR/TV indicator on the VCR disappears. No VCR operation from the infrared Remote Control. • Make sure the power plug is connected to an AC outlet. • Check batteries in remote control. Video or color fades in and out when making a copy of a video tape. • You cannot copy a copyrighted video tape. You are experiencing copy guard protection. SPECIFICATIONS Operating temperature : 5°C~40°C (41°F~104°F) Power requirement : 120V, 60Hz Converter output : VHF Channel 3 or 4. Power consumption : 14 Watts Dimensions : W 14-1/4” (360mm) H 3-5/8” (92mm) D 8-1/...