Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
(Fig. 1) Exhaust air must not be discharged into a wall cavity, unless the cavity is designed for the purpose. 0 There must be adequate ventilation of the room when the canopy rangehood is used at the same time as appliances burning gas or other fuels. © Always cover lit gas burners with pots or pans when canopy rangehood is in use. 0 Always switch off gas burners before you remove pots or pans. Do not leave lit gas burners exposed due to the risk of fire. (Fig. 2) Electrical Connection • Check that the mains voltage matches with the voltage on the data plate inside the canopy rangehood. • Check that the installation complies with standards of local gas and electricity authorities. • If the supply cord is damaged, it must be replaced by the manufacturer or its service agent of similarly qualified person in order ro avoid a hazard. LL Fig. 1 Fig. 2 electrolux e:line rangehood installation 3 Installation Mounting the hood body ÎÏ 190mm ± top flue fixing holes for recirculating mode bottom fixing holes for T-piece assembly top edge of motor housing key hole fixings for wall mounting hood base top of hob Depending on the preferred installation/ducting mode, follow step 5a or 5b below: 5. a) Recirculating Mode: Using the centre line, secure the flue fixing bracket to the wall with suitable screws, so that the location of the fixing holes are 63mm from the ceiling. Attach the recirculating T-piece to the flue fixing bracket using two M5x12mm screws (supplied). Secure bottom of T-piece assembly to wall using suitable screws. OR 5. b) Ducted Mode: Continue the centre line to the ceiling. Mark a line on the ceiling 14mm away from the wall. Locate the back edge of the flue cover mounting bracket on this line and centre. Screw the bracket to the ceiling using suitable screws. NOTE: Flue pipe shown is not included - must be purchased separately. 1. Using a spirit level mark a vertical centre line on the wall where the hood is to be positioned, and a horizontal line at the hood base position (refer Mounting the hood body). NOTE: The height of the underside of the hood body must be a minimum of 600mm above an electric cooktop & 650mm above a gas cook top and a maximum height of 800mm (refer to table below). Distance from hood base to top of hob hob type minimum* maximum gas 650mm 800mm electric 600mm 800mm * If the instructions of the hob specify a greater distance than the minimum above, this shall be the minimum height for installation 2. Mark the location for the four (4) key-hole fixings points, two at 243mm, and two at 363mm above the marked position of the hood base (refer Mounting the hood body). 3. Fix four (4) suitable screws (to support a total weight of 40kg) into the wall at the positions marked in step 2 to allow the body of the hood to be hung on the wall. Leave a 3-4mm gap between the face of the screw and the surface of the wall. NOTE: Screw head must be between 7mm and 11mm diameter, with screw thread diameter to be less than 5.5mm to suit key-hole slots.Total hood weight is 40kg. 4. Hang the body of the hood on the wall using the screws attached in step 3. To secure the hood body, use two (2) suitable screws and fix the top-edge of the motor housing to the wall. !\ important In recirculating mode, you must use carbon filters to eliminate cooking smells (Carbon filter model no. EFF72). NOTE: To ensure best performance of t...
Эта инструкция также подходит к моделям:Вентиляторы - ERCE90AS (869.09 kb)
Вентиляторы - ERCE90AS (869.09 kb)
Вентиляторы - ERCE90AS (869.09 kb)
Вентиляторы - ERCE90AS (869.09 kb)