Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Allow 1” (25mm) rear clearance for ventilation of the motor. Adequate clearance must be provided for servicing, ventilation and proper operation. The range must be kept clear of combustible material. Positioning The range should be installed on a firm, smooth and level floor designed to withstand the weight of the fully laden appliance. Place the range or salamander in desired position and level from side to side and back to front and diagonally. This leveling must be done with the unit under the hood and in it’s normal operating position. If the range is to be dais or cove mounted, the base on which it is to be set should be level. If it is not, the range must be shimmed to level. Legs All ranges are shipped from the factory with legs installed unless otherwise specified. When the range is specified for dais or cove base mounting, it is shipped less legs. Legs must be adjusted to a minimum height of 6” (152mm) in order to comply with NSF standards. Casters 1. The front casters on the unit are equipped with brakes to limit the movement of the range without depending on the electrical connection to limit appliance movement. 2. A restraint can be attached to the unit near the electric connection. If the restraint is disconnected, be sure to reconnect it after the range has been returned to its originally installed position. Ventilation Air The area in which the appliance is installed must be adequately ventilated to provide air for removal of steam, heat generated by the appliance, etc. These products are recommended to be installed under a ventilation hood. Proper operation of exhaust fans (proper speed, rotation and adjustment) is essential. The hood, and the filters must be cleaned on a regular bases and kept grease free. Installation Of Range Mount Salamander 1. The rear of the range must be easily accessible. 2. Place the salamander in position on the range. Slide the uprights into the opening at the oven rear. Secure the salamander uprights to the range with the hex head bolts provided. 3. Remove the terminal block access cover 4. Pass the wires though cable entrance hole. 5. Secure the cable connector 6. Terminate the salamander wire at the terminal block provided (Red to L1, Black to L2 or N, Green to GRN or E). NOTE: When mounting a salamander over an existing range in the field, an independent fussed connection must be made though the knock out plate provided in the main back of the salamander. Assembly of Backguard/High Shelf The back guard or high shelf will have been shipped separately. To install, put the backguard/high self on the rear of the range, slipping the uprights into the opening on each burner box side. Fasten the upright to the burner box side with four hex fasteners provided. Code Requirements The Garland S/SS680 series complies with the standards CSA C22.2 no.109 – latest edition, the UL197 – latest edition and the NSF#4 – latest edition. The installation and connection of this appliance must comply with current codes. In Canada – The Canadian Electrical Code Part 1 and in the USA – The National Electrical Code. The Garland SU680 series complies with the essential requirements of the Directives 73/23/EEC, 89/336/EEC, 89/392/EEC, 93/68/EEC and the standards, EN60335, IEC801.2, IEC801.3, IEC801.4, IEC801.5, IEC801.6 and IEC801.11. Electrical Supply Before attempting the electrical connection, the rating plate should be checked to ensure that the equipment’s electrical characteristics and supply electrical characteristics agree. On ranges and salamanders the supply entrance is located at the rear or alternatively on the main bottom. The supply terminal block is accessible from the front. The electrical supply must be adequate for the voltage, phase, and current marked on the rating plate. NOTE: A means of disconnection from the supply having a contact separation of at least 3 mm in all poles must be incorporated in the fixed wiring. This equipment is intended to be installed with fixed permanent wiring. WARNING: This appliance must be grounded. Single And Three Phase Connection Unless otherwise noted, all ranges are shipped from the factory for three phase connection. Salamanders are shipped from the factory for single phase connection. A wiring diagram is attached to the rear of each appliance. Visually check all electrical connections. The range is wired at the factory as specified on the order. If it is necessary to change the phasing refer to the wiring diagram. Commissioning Ensure all circuit breakers located in the lower compartment are set to the ON (1) position 1. Ensure that all controls are in the OFF position and turn on the main electrical supply. 2. Operate each section of the range or salamander in accordance with the instructions given in the Operating Instructions. 3. Check that the product functions correctly and that the voltage supply to the unit does not drop more than 5% when all sections are operated simultaneously. INSTALLATION Continued INITIAL OPERATION Prepar...
Эта инструкция также подходит к моделям:Вентиляторы - SS680 (353.1 kb)
Вентиляторы - SU680 (353.1 kb)