Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Only house the extractor in rooms with adequate ventilation. Remember that the extractor is powerful and whatever air is extracted needs to be replaced. • Do not tile the extractor in. It should be removable for service or maintenance. • Do not use silicone sealant to secure the hood to the wall. • You must be able to isolate the extractor from the mains electrical supply after installation. • This extractor has been designed to be used in a room with a volume of less than 36 m3. • Steam cleaners must not be used when cleaning this appliance. • The performance of your extractor will vary depending on a number of factors. These include: type of extraction, length of ducting, room volume, ventilation available and cleanliness of the filters. • Do not flambe under your extractor. Flames and fire can damage the extractor and this will invalidate any warranty provided. For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for Using your Extractor approximately 15 minutes after the end of cooking. A - Light switch B - Power indicator light C - Power switch AB A1 A2 C C1 C3 Fig. 1 C2 C4 To switch the extractor light on or off • Slide the light switch to position A1 for off, or A2 for on. To switch on the extractor, or change the motor speed • Slide the power switch to the position required dependent on the speed you require. To switch the extractor off • Slide the power switch to position C1 for off. Care and Maintenance IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean you extractor effectively by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth, for example the CDA E-Cloth. Cleaning the grease filter The grease filter should be kept clean to minimize the risk of fire. At least once a month you should remove and clean the grease filter with hot soapy water. To remove the grease filter, follow the steps below: 1. Unfasten the sliding brackets on either side of the cover panel and the cover panel will hinge open. 2. Remove the filter retaining wires from the cover panel. 3. Remove the grease filter and wash by hand in a lukewarm solution of water and mild detergent. Once clean squeeze the grease filter but DO NOT wring it out. Clean the filter holder using a dilute solution of water and mild detergent or with a damp cloth. Allow the grease filter to dry completely before reassembling the extractor. 4. Replace the grill panel and refasten the sliding brackets. 5. Replace the grease filter in the cover panel and reattach the filter retaining wires. Please note: The extractor must not be used without the grease filter in place. Changing the charcoal filter To ensure best performance of your extractor, you should replace the charcoal filters every four to six months, depending on use. Please note the charcoal filter cannot be washed. To attach a new charcoal filter, follow the steps below. 1. Unfasten the sliding brackets on either side of the cover panel and the cover panel will hinge open. 2. Place the charcoal filter on the centre of the motor support, and once firmly located turn the charcoal filter clockwise 90. until you hear a click which locks the charcoal filter into position. Replace the cover panel and refasten the sliding brackets. Fig. 2 c Changing the Light IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOVING IT. 1. Unfasten the sliding brackets on either side of the cover panel and the cover panel will hinge open. 2. Remove the faulty light bulb and replace with a light bulb no more powerful than that specified on the rating plate. 3. Replace the cover panel and refasten the sliding brackets. Do not touch bulbs or adjacent areas during or straight after prolonged use of the lights. The light is designed for use during cooking and not for general room illumination. Extended use of the light can reduce the lifespan of the bulb. Bulb replacement is not covered by the guarantee. Only use bulbs recommended for your extractor. Do not fit bulbs of a higher power rating. Bulbs of a lower power rating may be adequate for use, generally last longer, and use less energy. Spare bulbs are available from CDA Customer Care or from your local DIY shop. Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by ...