Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Applications The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude. Measured values are then shown on the display. Such features make this watch useful when hiking, mountain climbing, or when engaging in other such outdoor activities. Keep the watch exposed to bright light The electricity generated by the solar cell of the watch is stored by a built-in battery. Leaving or using the watch where it is not exposed to light causes the battery to run down. Make sure the watch is exposed to light as much as possible. • When you are not wearing the watch on your wrist, position the face so it is pointed at a source of bright light. • You should try to keep the watch outside of your sleeve as much as possible. Charging is reduced significantly if the face is covered only partially. l l l l l l l l l l l Bright light Solar cell • The watch continues to operate, even when it is not exposed to light. Leaving the watch in the dark can cause the battery to run down, which will cause some watch functions to be disabled. If the battery goes dead, you will have to re-configure watch settings after recharging. To ensure normal watch operation, be sure to keep it exposed to light as much as possible. Bright light Electrical energy All functions enabled LEVEL 1 LEVEL 2 LEVEL 3 Charge LEVEL 4 Solar cell (Converts light to electrical power.) Rechargeable battery LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4 Some functions disabled Discharge Battery charges in the light. Battery discharges in the dark. If the display of the watch is blank... If the display of the watch is blank, it means that the watch’s Power Saving function has turned off the display to conserve power. • See “Power Saving” for more information. Warning! • The measurement functions built into this watch are not intended for taking measurements that require professional or industrial precision. Values produced by this watch should be considered as reasonable representations only. • When engaging in mountain climbing or other activities in which losing your way can create a dangerous or life-threatening situation, always be sure to use a second compass to confirm direction readings. • CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any claims by third parties that may arise through the use of this watch. About This Manual • Depending on the model of your watch, display text appears either as dark figures on a light background, or light figures on a dark background. All sample displays in this manual are shown using dark figures on a light background. • Button operations are indicated using the letters shown in the illustration. • Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be found in the “Reference” section. (Light) General Guide • The illustration below shows which buttons you need to press to navigate between modes. • In any mode, press L to illuminate the display. • You can use buttons A, B, and C to enter a sensor mode directly from the Timekeeping Mode or from another sensor mode. To enter a sensor mode from the Data Recall, World Time, Stopwatch, Countdown Timer, Alarm, or Receive Mode, first enter the Timekeeping Mode and then press Timekeeping Mode the applicable button. Altimeter Mode World Time Mode Data Recall Mode Digital Compass Mode Press D. Press B. Countdown Timer Mode Press D. Press C. Sensor Modes Stopwatch Mode Barometer/ Thermometer Mode Press A. Alarm Mode Receive Mode • The actual level at which some functions are disabled depends on the watch model. • Frequent display illumination can run down the battery quickly and require charging. The following guidelines give an idea of the charging time required to recover from a single illumination operation. Approximately five minutes exposure to bright sunlight coming in through a window Approximately 50 minutes exposure to indoor fluorescent lighting • Be sure to read “Power Supply” for important information you need to know when exposing the watch to bright light. Operation Guide 3070 (B) 2 Radio-controlled Atomic Timekeeping This watch receives a time calibration signal and updates its time setting accordingly. •This watch is designed to pick up the time calibration signals transmitted in Germany (Mainflingen), England (Anthorn), and the United States (Fort Collins) and the time calibration signals transmitted in Japan. Current Time Setting This watch adjusts its time setting automatically in accordance with a time calibration signal. You also can perform a manual procedure to set the time and date, when necessary. •The first thing you should do after purchasing this watch is to specify your Home City (the city where you normally will use the watch). For more information, see “To specify your Home City” below. •When using the watch outside the areas covered by the time signal transmitters, you will have to adjust the current ...
Эта инструкция также подходит к моделям:Часы - 3070 (1.23 mb)