Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Hunter Fan, модель 83001

Производитель: Hunter Fan
Размер: 7.84 mb
Название файла:
Язык инструкции:enes
Перейти к скачиванию



Фрагмент инструкции


Secure the motor by tightening the 2 screws. 011_41949_EngS_2-12-08.indd 10 2/12/08 2:43:46 PM C12EFExisting Construction – accessible from above EXISTING FAN C11 NO EXISTING FAN 9”9.75” ORRemove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (9”x 9.75”). Cut out an opening for the housing. Use the motor housing as a template to mark position. Slide the mounting rails into brackets. position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. 5/81/25/81/2C13 C14 Mark position of screws by using holes as a template. 11 41949-01 02/12/2008 011_41949_EngS_2-12-08.indd 11 2/12/08 2:43:49 PM 41949-01 02/12/2008 12 C17 C18 C19 C20 C15 C16 Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. Attach the rails onto the screws. Tighten screws. Connect 4” duct and vent to the outside. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. Route wires through strain relief. For supply connection, use wires suitable for at least 90. C (194. F). 011_41949_EngS_2-12-08.indd 12 2/12/08 2:43:52 PM 41949-01 02/12/2008 13 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground C22 Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option Tighten the strain relief screws. Connect wires as shown. C24 I H C23 G Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. C21 011_41949_EngS_2-12-08.indd 13 2/12/08 2:43:55 PM 41949-01 02/12/2008 14 C25 I C26 J C27 ON OFF C28 Secure the motor by tightening the 2 screws. Turn on the power source. Test the motor. If the motor does not run, check the plug connection. C29 E1 Go to step on page 17 to attach grille. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. 011_41949_EngS_2-12-08.indd 14 2/12/08 2:43:58 PM 41949-01 02/12/2008 15 D11 EXISTING FAN F D12 Existing Construction – accessible only from below D13 2 1 D14 Route wires through strain relief. For supply connection, use wires suitable for at least 90. C (194. F). Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (9”x 9.75”). Move the housing into position above the ceiling Attach existing ducting to duct connector. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. F D15 Install the housing flush with the sheetrock and secure by tightening the pre-loaded screws into the joist. 011_41949_EngS_2-12-08.indd 15 2/12/08 2:44:00 PM 41949-01 02/12/2008 16 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground D16 Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option I D18 I D19 D20 J Connect wires as shown. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. Secure the motor by tightening the 2 screws. H D17 G Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. 011_41949_EngS_2-12-08.indd 16 2/12/08 2:44:03 PM 41949-01 02/12/2008 17 ON OFF D22 D23 E1 Go to step on page 17 to attach grille. D21 Test the motor. If the motor does not run, check the plug connection. Turn on the power source. Attaching the Grille Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS. N F E1 M E2 011_41949_EngS_2-12-08.indd 17 2/12/08 2:44:06 PM 41949-01 02/12/2008 18 Position the strain relief bracket between the plugs as shown, and screw into place. K E3 Align tabs on glass dome assembly with slots on light fixture, and insert tabs into slots. Install 2 Max 60 watt A-15 bulbs (Not Included). E8 Turn glass dome assembly as shown until it locks into position. E6 O E7 Attach thumbscrews. WARNING: To reduce the risk of electrical shock, all 4 thumbscrews MUST be properly installed. N E5 Align posts A, B, C and D (stamped into motor housing) with posts A, B, C and D (stamped into light fixture). Slide light fixture over posts. M E4 011_41949_EngS_2-12-08.indd 18 2/12/08 2:44:08 PM Trouble Shooting problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet.To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sur...

Эта инструкция также подходит к моделям:
Вентиляторы - 41949-01 (7.84 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории