Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
5. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 6. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will restart when it cools down. If the motor continues to shut off and restart, have the hood serviced. 7. For best capture of cooking impurities, the bottom of the hood should be a minimum of 24" and a maximum of 30" above the cooking surface. 8. Two installers are recommended because of the large size and weight of this hood. 9. This product is equipped with a thermostat which may start blower automatically. To reduce the risk of injury and to prevent power from being switched on accidentally, switch power off at service panel and lock or tag service panel. 10. Use with approved cord-connection kit only. 11. Please read specification label on product for further information and requirements. - 3 PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag (B080810285) containing: 2 - Mounting Brackets 8 - Mounting Screws (4,8 x 38mm Pan Head) 8 - Drywall Anchors 2 - Mounting Screws (3,9 x 9,5mm Pan Head) 2 - Mounting Screws (3,9 x 9,5mm Pan Head Black) 1 - Flue Mounting Bracket 1 - Installation Instructions MOUNTINGBRACKETS DECORATIVE FLUE 2 MOUNTING SCREWS (3,9 x 9,5mm Pan Head) 2 MOUNTING SCREWS (3,9 x 9,5mm Pan Head Black) FLUE MOUNTING BRACKET 8 DRYWALL ANCHORS 8 MOUNTING SCREWS (4,8 x 38mm Pan Head) - 4 INSTALL THE DUCTWORK NOTE: To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions will reduce the performance of the hood. Use as few of them as possible. 4. Install a roof or wall cap. Connect 6" round metal ductwork to cap and work back towards hood location. Use duct tape to seal the joints between ductwork sections. INSTALL MOUNTING BRACKETS 1. Construct wood wall framing that is flush with interior surface of wall studs. Make sure: a) the framing is centered over installation location. b) the height of the framing will allow the mounting brackets to be secured to the framing within the dimensions shown. 2. After wall surface is finished, secure mounting brackets to framing at dimensions shown, using screws provided. INSTALL THE HOOD 1. Hang the hood from the brackets through the rectangular cut-outs on the back of the hood. Cut-outs are larger than the brackets to allow for horizontal adjustment. The bottom of the hood should be 24" to 30" above the cooking surface. 2. Height adjustment screws provide vertical adjustment. 3. Depth adjustment screws provide horizontal adjustment. 4. Secure the hood with mounting screws (4.8x38mm). Use drywall anchors, provided, if wall studs or framing are not available. 6” ROUND ELBOW WALL CAP ROOF CAP 6” ROUND DUCT 24” TO 30” ABOVE COOKING SURFACE DECORATIVE FLUE HOOD FRAMING BEHIND DRYWALL 435/8"to495/8"above cooktop 415/16" 415/16" 435/8"= bottom of hood 24" above cooktop 495/8"= bottom of hood 30" above cooktop RECTANGULAR MOUNTING WALL FRAMING SCREWS (4.8x38mm) CUTOUTS MOUNTING BRACKETS DEPTH ADJUSTMENT SCREWS HEIGHT ADJUSTMENT SCREWS - 5 WIRING Note: This range hood must be properly grounded. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. 1. Remove the wiring box cover. Remove a knockout from the wiring box. 2. Secure the conduit to the wiring box through a conduit connector. 3. Make electrical connections. Connect white to white, black to black and green to green. 4. Replace wiring box cover and screws. Make sure that wires are not pinched between cover and box. CONNECT DUCTWORK 1. Use screws (4.8x38mm) and wall anchors (provided) to secure flue mounting bracket to the ceiling or wall as shown. 2. Use 6" round metal duct to connect the duct collar on the hood to the ductwork above. 3. Use duct tape to make all joints secure and air tight. WIRING BOX COVER FLUE MOUNTING BRACKET MOUNTING SCREWS (4.8x38mm) DECORATIVE FLUE DUCT TAPE 6" ROUND METAL DUCT - 6 INSTALL DECORATIVE FLUE 1. Hold the decorative flue near the top of the hood. Connect the switch cable from the hood to the decorative flue, as shown. SWITCH CABLE 2. Slide the lower decorative flue section downward and into the channels on the hood. LOWER DECORATIVE FLUE SECTION CHANNEL CHANNEL 3. Raise upper decorative flue section and UPPER DECORATIVE attach it to the flue mounting bracket with FLUE SECTION screws (supplied) - 3.9x9.5mm. FASTEN TO FLUE MOUNTING BRACKET WITH SCREWS (3.9x9.5mm) - 7 MAINTENANCE Proper maintenance of the Range Hood will assure proper performance of the unit. Grease Filter Clean the grease filter frequently. Remove the grease filter by pulling it down ward. Use a warm detergent solution. Grease filter...