Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
* When the heat control is set to ‘ ‘ for cool blow, set the thermostat control to maximum. Position ‘ ‘ will turn the heater on and off to maintain a temperature of approximately 5°C. - OFF - Cool Blow* - Half heat - Full heat Heat Control - see Fig. 2 (IP21) H W D 265 230 230 Model(s) Specification DXUFSR2 2.0kW Thermostat & Switch Fig. 2 Fig. 3 (see Fig. 3) Fig. 1 (see Fig. 2) IMPORTANT SAFETY ADVICE DO NOT use the heater on deep pile carpets or the long hair type of rugs, or less than 750mm (30") away from any overhanging surface. Keep combustible materials such as drapes and other furnishings clear from the front, sides and rear of the heater. Do not use heater to dry your laundry. DO NOT use the heater in the immediate surroundings of a bath, a shower or a swimming pool. DO NOT place the heater directly below a fixed socket outlet. The socket-outlet must be accessible at all times to enable the mains plug to be disconnected as quickly as possible. DO NOT COVER or obstruct the air inlet and outlet openings in any way. The heater must be on a flat stable surface when in use. DO NOT operate the heater with the mains lead overhanging the front outlet grille. The appliance is designed to self-right itself if it is accidentally knocked over, however the appliance should not be maltreated to perform this function. ALWAYS ENSURE THE APPLIANCE DOES NOT COME TO REST ON THE MAINS LEAD OR ALLOW THE LEAD TO BECOME WRAPPED AROUND THE APPLIANCE - THIS MAY IMPAIR THE SELF-RIGHT FUNCTION. NEVER leave the heater unattended when it is used by or near the aged, infirm person’s or children. THE HEATER CARRIES THE WARNING SYMBOL INDICATING THAT IT MUST NOT BE COVERED. The instruction leaflet belongs to the appliance and must be kept in a safe place. If changing owners, the leaflet must be surrendered to the new owner. IMPORTANT – If the mains lead of this appliance is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. WARNING: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. Electrical connection This heater must be used on an A.C.~ supply only and the voltage marked on the heater must correspond to the supply voltage. This heater is fitted with a plug incorporating a 13 amp fuse. When replacing the fuse, a 13 amp fuse approved by ASTA to BS 1362 must be used. If the plug is not suitable for the socket outlets in your home, the plug must be cut off and an appropriate one fitted. A plug cut off from a mains lead will give a shock hazard if inserted into a 13 amp socket elsewhere in the house. To avoid this, it should be disposed of immediately. IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE NOTE: The fuse cover of a non-rewirable plug must be refitted when changing the fuse. Should the cover become lost, the plug must not be used until the correct replacement fuse cover is obtained from your supplier or by contacting our customer helpline. IMPORTANT : The wires in this mains lead are coloured in accordance with the following code : BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead may not correspond with the coloured markings in your plug, proceed as follows : Connect the BROWN wire to the terminal marked ‘L’ or coloured RED. Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK. Note : ‘L’ or ‘N’ must not be connected to the EARTH terminal marked ‘E’ or or coloured GREEN or GREEN AND YELLOW. If in doubt, consult your electrician. Safety - overheat protection After Sales Service For your safety, this appliance is fitted with a thermal cut-out. In the event that the product overheats, the cut-out switches the heater off automatically. To bring the heater back into operation, remove the cause of overheating, then turn off the electrical supply to the heater for a few minutes. When the heater has cooled sufficiently reconnect and switch on the heater. If the cut-out operates repeatedly, contact your supplier. Cleaning WARNING ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER. Do not use detergents, abrasive cleaning powders or polish of any kind on the heater. Wipe with a dry cloth to remove dust and a damp cloth (not wet) to clean off stains. Be careful not to allow moisture into the heater. Ensure that dust or fluff does not accumulate inside the heater as this could lead to overheating of the element. Use a vacuum cleaner to remove any fluff which does accumulate. Recycling For electrical products sold within the European Community. At the end of the electrical products useful life it should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country. Yo...