Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Note: If the hood is to be installed onto a hollow construction or plaster or partition board wall then special fixing screws will be required (not supplied). Fitting the Canopy Hood • Screw the two screws item 12d supplied onto the brackets 7.1. • Hook the hood body onto the bracket 7.1, centring it around the vertical line. • Use the adjusting screws item 12d underneath the hood to level the hood body Extraction (Ducted) The cooker hood is more effective when installed in the extraction mode (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be evacuated through an outside vent of o125 (5ins) or o150mm (6ins). The ducting used must be manufactured from fire retardent material conforming to the relevant British Standard or DIN 4102-B1. When the cooker hood is ducted to the outside the charcoal filter must be removed. Fitting the Ducting • Fit the o150mm (6ins) ducting to the spigot on top of the hood body as illustrated. • When using o125mm (5ins) ducting fit item 9 and 10 on to the spigot on the top of the hood body as illustrated. • For the best performance use the shortest possible run of ducting and we recommend the use of rigid pipe in preference to flexible hose as this will improve the flow of air while reducing turbulence, which causes noise and a loss of performance. • If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler, then its flue must be be of the room sealed or balanced flue type. • If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. • The cooker ducting when fitted in the extraction mode must never be connected to central heating flues, radiators or water heaters. Recirculation Mode The cooker hood is supplied specified for use in the recirculation mode, with the charcoal filter fitted. In the recirculation mode contaminated air is passed through the charcoal filter to be purified and recirculated into the kitchen through the grille outlets on either side of the chimney. • Push fit the air outlet connector item 15 onto the air outlet. • Ensure the activated charcoal filter has been fitted. Fitting the Upper Chimney • Slightly widen the two sides of the upper chimney and hook them behind the brackets item 7.2.1 ensuring they are correctly seated. • Secure the sides to the brackets using the 4 screws item 12c (2.9 x 9.5mm) supplied. Fitting the Lower Chimney • Slightly widen the two sides of the lower chimney and hook them between the upper chimney and the wall, ensuring they are correctly seated. • Fix the lower chimney to the hood body using 2 screws item 12c (2.9 x 9.5mm) supplied. • Make sure that the air outlet connection is aligned with the chimney outlets. Electrical Connections DOUBLE INSULATED DO NOT EARTH Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole.A Switched Fuse Connection Unit to BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. This appliance conforms to BS 800: 1988 and EEC Directive No. 78 308 regarding suppression of radio and television interference. Using the cooker hood The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. The appliance can be installed to recirculate or extract contaminated air. Cooker Hood Controls The cooker hood functions are controlled by four push button switches located centrally in the control fascia. Turns the worktop lighting On and Off S Mains light - illumination indicates fan motor is running V1 Motor ON/OFF switch. Depress to turn the extractor motor on at a LOW speed, to ensure that light cooking vapours are silently extracted. V2 Medium speed, suitable for general use. This speed provides an optimum treated air flow to noise level ratio. V3 Maximum speed, used to extract intensive levels of cooking vapour emissions. To Operate Select the required fan speed and light if required. Recirculation In the recirculation mode the contaminated air ent...
Эта инструкция также подходит к моделям:Вентиляторы - JLBIHD902 (309.2 kb)