Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
If the speed is not displayed, check that conditions A and B are satisfied. To the sensor Cut Toward the sensor line When attaching the bracket to the handlebar Caution: Tighten the bracket, ensuring that the cable does not get caught in the stem. Caution: Tighten the bracket, ensuring that the cable does not get caught in the handlebar. B The clearance between the sensor surface and the magnet must not exceed 5 mm. Attach the bracket to the stem or handlebar When attaching the bracket to the stem Wrap the cable around the front brake cable Caution: Turn the handlebar to make sure wire does not hinder full rotation. Caution: Round off the cut edge of the bracket band to prevent injury. Install the sensor and magnet : A The magnet should pass through the sensor line. * You can also use ties 0 (in place of sensor rubber band 6) to secure the sensor. Install the sensor Install the magnet Click While supporting it by hand, push it out as if lifting the front up * For wing type handlebar or oversized stem, bracket can be mounted using the Bracket Holder and nylon ties. (Option). How to install the unit on your bicycle 1Bracket band 2Bracket 3Nut 4Sensor 5Magnet 6Sensor rubber band (x2) 7Sensor hook 8Sensor rubber pad (x3) 9Bracket rubber pad 0Nylon ties (x5) CATEYE STRADA CYCLOCOMPUTER CC-RD100N ENG Before using the computer, please thoroughly read this manual and keep it for future reference. U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending Copyright© 2008 CATEYE Co., Ltd. CCRD10-080924 066600507 6 WARNING / CAUTION • Do not concentrate on the computer while riding. Ride safely! • Install the magnet, sensor, and bracket securely. Check these periodically. • If a child swallows a battery, consult a doctor immediately. • Do not leave the computer in direct sunlight for unnecessary or extended periods. • Do not disassemble the computer. • Do not drop the computer. Doing so may result in a computer malfunction or damage. • When using the computer installed on the bracket, change the MODE by pressing on the three dots below the screen. Pressing hard on other areas can result in malfunction or damage to the computer. • Never place the computer on a metal surface. If you do, the contact points will conduct electricity, discharging the battery. • Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket threads. • When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol. • Dispose of used batteries according to local regulations. • LCD screen may be distorted when viewed through polarized sunglass lenses. MODE AC MENU MODE MENU MODE MENU MODE MODE MENU MODE Switch the screen or move digits (by pressing & holding) Enter the tire circumference Enter the tire circumference of your bicycle in mm. * Refer to the tire circumference reference table. 1 2 3 4 km/h - mph Increase Move digits (by pressing & holding) Register the setting Register the setting Clear all data (initialization) Press the AC button on the back. Select the desired speed units Select “ ” or “ ”. 24h - 12h, or increase the value Register the setting (finish) Preparing the computer Set the clock When MODE is pressed and held, “Displayed time”, “Hour”, and “Minute” will appear, in this order. Battery case cover Contact Push! : Speed unit : Wheel size icon When the computer is mounted on the bracket AC Measure wheel circumference (L) of your bike To get the most accurate calibration do a wheel roll out. With the valve stem perpendicular to the ground, mark the pavement at the valve stem. With the riders weight on the bike, roll the wheel one tire revolution in a straight line and mark the ground when the valve stem is perpendicular to the ground again. Measure the distance in millimeters. This is the most accurate wheel calibration number. COINCOINCOIN Close Open CC-RD100N Wheel selection ..... Toggle between the specified wheel size (tire circumference) and . Use this function if the computer is to be shared between two bicycles. Pressing MODE toggles between and . Wheel size entry .... Pressing MODE increases the value, and pressing and holding MODE moves to the next digit. * To enter the wheel size , display using “Wheel selection”. Clock setting .......... To set the clock, refer to “Preparing the computer-4”. Total distance manual entry ................................ Before reinitializing the computer, note the total distance. This reading will later allow you to enter the total distance manually. Pressing MODE increases the value, and pressing and holding MODE moves to the next digit. Speed unit .............. Pressing MODE toggles between and . Maintenance To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth. Replacing the battery If the display appears faded, replace the battery. Install a new lithium battery (CR1620) with the (+) side facing upward. Then reinitialize the computer referring to “Preparing the c...