Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Instruct children not to bounce or lean, which can cause a shift of weight. Do not make high-speed turns or descents when pulling the trailer. Always corner with caution at 5 mph or less, as the trailer cannot lean into a turn the way a bicycle can. Do not travel faster than 15 mph—all road irregularities and your slower reaction time are greatly magnified. Trailers can tip over, causing damage to trailer and serious injury to cyclist or passengers. AVOID causes of tip over, especially: WARNING• Children leaning or bouncing• Hitting potholes, curbs, other road obstructions• Taking turns too fast• Sudden swerving• Off-banked turns• Improper wheel installation• Improper tire inflation No Motorized Vehicles Never pull your Burley trailer with a motorized vehicle, as the increased acceleration and speed could damage the trailer or cause it to tip over. Always Use Your Cover To protect your children from flying debris, always use your cover. Never leave children unattended in direct sunlight, as heat buildup in the trailer can cause serious harm. Open or close the vinyl window and periodically check to make sure your children are comfortable. Wear Helmets Numerous studies have shown that head injury is the leading cause of bicycling fatalities. Helmets prevent or reduce bicyclists’ head injuries; it is essential that both cyclist and passengers use approved bicycling helmets at all times. Proper Wheels and Tires are Essential Use only the factory-supplied wheels, and keep them properly maintained. Inflate tires to 30–35 P.S.I. and check pressure before each use. Do not use higher-pressure tires or knobbies. We recommend using only tires with street tread. Know Your Trailer Hitch Clamp the hitch securely to the bicycle frame, and check for a tight attachment each time you use the trailer. Refer to “Hitching Your Burley to Your Bicycle” and “Maintenance and Storage” sections of this manual for proper installation, use and maintenance of your hitch. Use Your Flag Always use the safety flag—it will help make you more visible to motorists and other cyclists. Protect Your Children Use the shoulder harness, lap belt, and child helmets on your children at all times. Always fasten the seat belt so that each child is held securely. For maximum stability and safety, seat a single child in the center of the trailer. Periodically check placement of the shoulder straps, especially for sleeping children. Make sure children cannot put a finger into the wheel spokes. Observe Age and Height Restrictions The trailer seat is intended only for children old enough to wear a helmet and sit upright and alone. Adequate neck strength is required to hold his/her head upright while trailering. A physician should evaluate anyone who is of questionable developmental age for trailering. Never carry a child whose sitting height (with helmet) is above the roll bar, because their chance of injury is significantly higher in the event of a tip over. Hardware Bag Contents and Tool List Hardware Bag Contents: Tools Required: All: Warranty Card, Burley Owner’s Instruction & Safety Manual d’Lite™, Encore™, Solo™, Lady Bug™: (2) red reflectors Phillips screwdriver (2) clear reflectors (2) reflector brackets (4) hex head screws (1) hitch Bee™: (2) red reflectors (2) hex head reflector screws (2) 1” plastic reflector brackets Phillips screwdriver (1) hitch Cub™: (1) Cub Brake Assembly Two No. 2 Phillips screwdrivers (3) #10 x 5/8 Phillips pan screws (3) #10 spring washers (3) #10 x 1” fender washers (1) hitch Note: European models have an additional light hardware bag. Unfolding Your Burley Trailer To unfold your trailer, rotate the front tube upward and the rear tube back until they meet on the two plastic saddles. Then rotate the two frame locks to snap onto the rear tube. The frame locks should connect adjacent to, and to the outside of, the two plastic saddles. d’Lite™, Encore™, Lady Bug™, Cub™ – After the frame locks are locked in place, attach the hooks on the seat sides to the D-rings by the windows inside the trailer. Solo™ only – After the frame locks are locked in place, clip the female buckle ends on the two seat side straps into the male buckle ends on the inside of the frame. Check that the frame locks are properly engaged before using the trailer. Failure to do so can result in serious injury. WARNING IMPORTANT: Please verify that you have received all of the contents listed. Do not proceed with assembly if any parts are missing; contact Burley immediately for replacement parts. Front Rear Seat clips Frame locks snapped into closed position onto rear tube. Seat clips attach to the top of the frame. Mounting the Reflectors Cub™: Factory-installed Bee™: Rear Reflectors Only All other models: FRONT: Clear front reflectors are mounted horizontally to both sides of the trailer fabric front. “TOP” is marked on the reflector front. Locate the grommets on the trailer fabric front, insert the screw into the reflector back through the grommet, and ti...
Эта инструкция также подходит к моделям:Велосипеды - LADY BUG (1.28 mb)
Велосипеды - SOLO (1.28 mb)
Велосипеды - BEE (1.28 mb)
Велосипеды - d'LITE (1.28 mb)