Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Control lamp The control lamp will light when the fryer is switched on and will switch off when the set temperature is achieved. The light will come on and off in line with the thermostat regulation of the temperature. Frying Make sure the heating element is positioned at the bottom. Oil is poured into the frying container. The “Min” mark must be observed. This corresponds to an oil content of 1,5 liters. Maximum amount of oil in the container is 3,5 litres. The grill elements stay turned down and the fryer may be switched on at the desired temperature setting. The lid may be on the fryer to shorten the preheatingtime. NB!! Grill and fryer cannot be used at the same time. Overheating protection Overheating protection during any overheating of the oil at the fryer will switch the inserted overheating protection off the friteuse. Customer service for the remedy of the disturbance contacts. you can place the steel lid on top of the . The heating elements and the oil will stay hot long time after the combi-grill has been shut off. Do never pour water into the hot oil as the water explosively will start boiling Splashquar. The splashquard can be removed to make it easier to clean the surface. What to do: 1. Hold the splashquard as shown in the diagram 2. Lift the splashquard straight up 3. Clean the top surface as described in “cleaning the steel surface” Be aware of the two retaining pegs, which are sharp. 4. Replace the splashquard in position ENSURE that it is fitted the correct way Never use hard or sharp implements to lift off the splashquard.. Do not wash the splashquard in a dishwasher. The hob must not be used with the splashquard off. Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. For more severe soiling, use a liquid scouring cream. Always clean the steel in the direction of the steel finish. To ensure that the steel retains its shine, it is recommended that you use a polishing agent for stainless steel on a regular basis. Always polish in the direction of the steel finish (cross-wise). Never use steel wool, metal sponges or other abrasive cleaning agents. The Grill The grill must be cold before cleaning. The grill grid The grilling grid should be cleaned after each use. 1. Remove burnt-in fat and bits of food with a scouring pad. If the grid is heavily soiled you can let it soak in warm water with washing up liquid. 2. Clean the grilling grid with washing up liquid or in the dishwasher. 3. Apply a thin coat of cooking oil to the grid The lava stone It is not necessary to clean the lava stones after each use. The lava stones absorb and burn fat during use. Clean the stones when they have become very soiled. You can clean the stones in two ways. 1. Boil the stones in water added washings up liquid. 2. Place the stones in the frying basket and wash it all in the dishwasher. Replace the lava stones when they can not be cleaned satisfactory by the described methods. New stones may be bought from your white goods dealer. The heating elements Normal the heating elements will burn of fat during use but if the heating elements get very soiled by fat or bits of food you can clean them with a hard brush. The fryer You can leave the oil in the container from time to time. How often you need to change the oil depends on how often you use the fryer and for what. You should change the oil and clean the frying container when the oil changes colour and/or if the oil begins to smell. . 1. Remove the safety shield from the drain cock. 2. Place a bowl under the drain cock. Make sure the bowl is large enough to hold the oil in the container. 3. Open the drain cock and let the oil run into the bowl. 4. Close the drain cock. The frying container The drain cock must closed. 1. Remove the metal filter and wash it in warm soap water. 2. Pour warm water with washing-up liquid in the container. You can leave the heating element down when cleaning the container. Clean the container with a brush. 3. Place a bowl under the drain cock. Make sure the bowl is large enough to hold the water in the container. 4. Open the drain cock and let the water run into the bowl. 5. Rinse the container in cold water. Remember to place a bowl under the drain cock to catch the rinsing water. Eventually wipe the container with a dry clotts. 6. Close the drain cock and replace the safety shield. Place the metal filter with the curved side upwards over the drain hole in the container. #$ . Element voltage 240 V Electrical connections 240 V, 1 phase, neutral + earth Total power consumption 2300 W This unit is labelled to indicate conformity with the low voltage directive ( 73/23/EEC ) and the EMC directive ( 89/336/EEC ). . The hob unit can be mounted in any type...
Эта инструкция также подходит к моделям:Варочные панели - 949600686 (292.37 kb)
Варочные панели - 949600686 (292.37 kb)
Варочные панели - 949600686 (292.37 kb)