Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Tune the station to be preset as described in “Au- tomatic/Manual tuning”. 2. Press SETUP. “M. PRESET” appears on the win- dow display, then the preset position number blinks. 3. Press PRESET + or – to select the position num- ber to be preset. 4. Press ENTER. The preset position number stops blinking and now the station is preset in the memory. 5. Press SETUP. The preset position number disap- pears. 6. For presetting of other stations, repeat steps 1 ~ 5 above. Presetting the radio stations Automatic presetting 1. Press DVD/FM/AM to select FM or AM. 2. Press SETUP for 2 seconds. “A. PRESET” ap- pears on the window display, then starts the au- tomatic presetting from the low end of FM band to the AM band. After all FM and AM stations have been preset, au- tomatic presetting stops and the station memorized position 1 will be listened. You can preset 30 stations for FM and AM. Tuning the radio stations Press DVD/FM/AM to select FM or AM. “TUNER FM” or “TUNER AM” appears on the win- dow display for 3 seconds and changes to radio operation mode. Automatic tuning Press and hold TUNE + or – for 1 second to start the automatic tunning.The scanning stops when the unit tunes in a station. Press the button again to tune the other stations. Manual tuning Press TUNE + or – briefly to tune in a station. The frequency changes in 50 kHz steps for FM and 9 kHz steps for AM. 1 2 36 2D20401A P32-BACK 36 26/9/03, 6:03 PM Listening to the radio Reception of RDS (Radio Data System) stations Preset the radio stations first as described on page 36. RDS (Radio Data System) is a system gradually being introduced on FM in many countries, where by an inau dible stream of data is transmitted in addition to the nor mal radio signal. This data contains various information including station/transmitter identification, traffic informa tion and a list of alternative frequencies for the radio sta tion being received. Press PRESET + or – to select the desired position number. You can also select the desired position num- ber using the number buttons (0–9), then press ENTER. • For example, to select the preset position number 7, press 0 and 7, then press ENTER. To select the preset position number 25, press 2 and 5, then press ENTER. Press DVD/FM/AM to select FM or AM.1 2 Adjust the volume by rotating Volume knob on the front panel or VOL +/– on the remote con- trol. 3 Notes: • RDS is only available for FM reception. • The PS (PROGRAM SERVICE) NAME is displayed auto- matically when a RDS station is received. Press DVD/FM/AM select FM.1 2 Select a desired station by pressing the PRE- SET + or –. When the RDS transmission is re- ceived, the RDS indicator and the programme service name (PS) appear on the display win- dow. 37 2D20401A P32-BACK 37 26/9/03, 6:03 PM Other functions Sleep timer Mute You can set the DVD receiver to turn off automati- cally at a specified time. Press SLEEP to set the desired sleep time. The SLEEP indicator and sleep time appears on the display window. Each time you press SLEEP, the setting changes in the following order. SLEEP 120 110 100 ... 30 20 10 0(off) Notes: • After the sleep timer is programmed, the remaining timer appears briefly every ten minutes on the display window. • To confirm the sleep timer setting, press SLEEP. • The remaining time appears on the display window. This function will change the brightness of the display window and the control buttons on the front panel during Power-on status. Press the DIMMER to dim the display window. To cancel the Dimmer function, press DIMMER again. Press and hold DIMMER for 3 seconds to dim the control buttons. To cancel the Dimmer function, press and hold DIMMER for 3 seconds again. Dimmer 38 Press MUTE to mute your unit. You can mute your unit in order, for example, to answer the telephone, “MUTE” indicator appears on the display window. Connect a stereo headphone plug (o 3.5mm) into the HEADPHONE socket on the front panel. The speakers are automatically disconnected when you plug in the headphones (not supplied). Note: When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage. Selecting input source You can use VCRs or other units connected to the LINE IN 1 or LINE IN 2 connectors. Press INPUT SELECT repeatedly on the remote control to select the desired input source. Note: The Optical/Coaxial input function is available only when the other unit’s Sampling Frequency is as follows. PCM: 32KHz, 44.1KHz, 48KHz Dolby Digital: 48KHz DTS: 44.1KHz, 48KHz Depending on the setting or the combination of the other unit, the sound may not be played correctly. Screen saver The screen saver operates when you leave the unit in DVD stop mode for about five minutes. Using headphone socket 2D20401A P32-BACK 38 26/9/03, 6:03 PM Before calling service personnel Check the following guide for the possible cause of a problem before contacting service. Symptom No power. No picture. No soun...