Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
NOTE: If you try to enter the programming mode while the computer is cooking, the display will flash BUSY. NOTE: The unit comes from the factory configured to display in degrees Fahrenheit. To toggle back and forth between Fahrenheit and Celsius, press the Program Mode switch, then enter the code 1 6 5 8by pressing the corresponding product buttons. Next, press the Temperature Check/Program Lock switch to lock in the new display option. 3. Enter the number 1 6 5 0 by pressing the corresponding product buttons. Unless this code is entered, programming will not be accepted. This is to prevent unauthorized changes to your current instructions. 4. SP-r (Setpoint) will appear in the left LED display. Any previously programmed temperature setpoint will appear in the right display. To change the setpoint, enter the desired setpoint temperature using the corresponding product buttons. The setpoint can be programmed for any value up to 212°F (100°C). Press the Program Mode switch to lock in the new setpoint (or the old setpoint, if it was not changed). 5. SELP (Select Product) will appear in the left display. Press the product button to be programmed (or press to return to the normal operating mode). 6. COOC (Cook Time) will now show in the left display. Any previously programmed cooking time will appear in the right display. Pressing will accept the current cooking time. To change the cooking time, enter the new time using the product buttons. The cook time can be programmed up to 59:59. Press to lock in the new time. 3-6 NOTE: The computer can be programmed for either “standard” or “slow” clock speed. The standard clock displays minutes and seconds, the slow clock displays hours and minutes. To toggle back and forth between clock speeds, press the Program Mode switch, then enter the code 1 6 5 3 using the product buttons. To determine if the clock speed is set to standard or slow, initiate a cook cycle by pressing a product button. If the computer is set to the standard clock, the time in the LED display will immediately begin to count down. If it does not, the computer is set to the slow clock. 7. Sh1 (Stir Time 1) appears in the left display. If your product requires stirring during the cooking process, set the number of seconds to cook before stirring using the product buttons. If your product does not require stirring, enter “0”. The number entered will appear in the right display. The stir time can be programmed up to 59:59, but cannot exceed the product cook time. Press to lock in the programmed time. Sh2 will appear. Program the time of the second stir time as above. Be sure the time entered is greater than Sh1 or else is “0”. Sh3 will appear. Program the length of the third stir time in the same manner as for Stir Times 1 and 2. Be sure that the time entered is greater than Sh2 or else is “0”. For example, entering “30” means the product needs to be stirred after it has been cooking for thirty seconds. At the end of thirty seconds, an alarm will sound and the product switch will flash until cancelled by the operator pressing the product button. CAUTION Remember: Sh2 must be greater than Sh1 (or else be “0”). Sh3 must be greater than Sh2 (or else be “0”). None of the stir times can be greater than the cook time entered in Step 6. 8. SELP (Select Product) will again appear in the left display. If more products are to be programmed, follow Steps 5 through 8 for each additional product. 9. When you complete your programming, lock in the whole program by pressing the Temperature Check/Program Lock Switch . 3.2.2 Operating the Computer Turn the computer on by pressing the Power switch. NOTE: A decimal between digits 1 and 2 in either LED Display indicates the unit is heating. 1. One of the following will normally be displayed: a. °-Lo, indicating that the water temperature is 11°F (6°C) lower than the setpoint. b. “- - - -” indicating that the water temperature is in the cooking range. NOTE: For best results, cooking should not be attempted unless the display indicates “- - - -”. 3-7 NOTE: You may also see one of these indicators of abnormal operation: • °-Hi, indicating that the water temperature is 11°F (6°C) higher than the setpoint • HELP, indicating a heating problem. • Prob, indicating that the computer temperature probe circuit is open. 2. Press a product button to start a cook cycle. a. The programmed cook time will appear and the countdown begins. b. If stir times are programmed, the operator will be notified to agitate the product a predetermined number of seconds after the cook cycle has begun. An alarm will sound, the display will read Sti r, and the LED in the product button will blink. To cancel the alarm, press the indicated product button. If no stir times have been programmed, Sti r will not appear during the cook cycle. CAUTION Pressing the product button twice while the Sh alarm sounds will cancel the cook cycle as well as the alarm. c. At the end of the cook cycle, an alarm will sound, COOC w...
Эта инструкция также подходит к моделям:Варочные панели - 17EC (3.81 mb)
Варочные панели - ESW (3.81 mb)
Варочные панели - EWBS (3.81 mb)