Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
OPERATIng fireplace Continued Sensor Rod Pilot Burner Piezo Ignitor OFF PILOT LO IH ONOFFREMOTEONOFFON Figure 67 - Pilot Assembly (Electronic) Figure 65 - Setting the Selector Switch, Gas Control Knob and Variable Control Knob for Remote Operation Inspecting Burners Check pilot flame pattern and burner flame patterns often. pilot assembly The pilot assembly is factory preset for the proper flame height. Alterations may have occurred during shipping and handling. Call a qualified service person to readjust the pilot if necessary. The position and pattern of the pilot flames in relation to the sensing devices should be as shown in Figures 66 and 67 depending on model. If you pilot assembly does not meet these requirements: • turn fireplace off (see To Turn Off Gas to Appliance, page 32 or 35 depending on model) • see Troubleshooting, page 38 BURNER FLAME PATTERN Burner flames will be steady; not lifting or floating. Flame patterns will be different from unit to unit and will vary depending on installation type and weather conditions. If the vent configuration is installed incorrectly, the flames will lift or "ghost". This can be dangerous. Inspect the flames after installation to ensure proper installation and performance. Figure 68 shows a typical flame pattern. If burner flame pattern differs from that described: • turn fireplace off (see To Turn Off Gas to Appliance, page 32 or 35 depending on model) • see Troubleshooting, page 38 Thermopile 3/8" to 1/2" Pilot Burner 1/8" Thermocouple Figure 68 - Typical Flame Pattern Piezo Ignitor Figure 66 - Pilot Assembly (Millivolt) Cleaning and Maintenance WARNING: Turn off fireplace and let cool before cleaning. CAUTION: You must keep control areas, burners and circulating air passageways of fireplace clean. Inspect these areas of fireplace before each use. Have fireplace inspected yearly by a qualified service person. Fireplace may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc. GLASS DOOR WARNING: Handle glass door panel with care. Do not strike, slam or otherwise abuse glass. Do not operate fireplace with the glass door unlatched, removed, cracked or broken. WARNING: Do not use abrasive cleaners as this may damage glass. Use a nonabrasive household glass cleaner to clean glass. Do not clean glass when hot. Glass must be cleaned periodically. During start-up it is normal for condensation to form on the inside of the glass causing lint, dust and other airborne particles to cling to the glass surface. During initial start-up a slight film may form on the glass due to paint curing. The glass should be cleaned several times with a non-ammonia, nonabrasive household cleaner and warm water after the first two weeks of operation. Thereafter, clean the glass two or three times during each heating season, depending on the usage and circumstances present. Refer to Removing/ Replacing Glass Door, page 29 of this manual when removing glass door for cleaning. WARNING: Only parts supplied by the manufacturer should be used when replacing broken or damaged glass door panel (see Replacement Parts, page 44). This glass door panel is a complete unit. No substitute materials may be used. CAUTION: Wear gloves and safety glasses while handling or removing broken glass. Do not remove if glass is hot. Keep children and pets away from glass. If glass has been broken, carefully remove glass door (see Removing/Replacing Glass Door, page 29). Vacuum all glass pieces with a shop vac. CAUTION: Do not vacuum if pieces are hot. Use only the tempered glass door replacement intended for this fireplace (see Replacement Parts, page 44 for detail on ordering). No substitutions may be made. See Removing/Replacing Glass Door, page 29 for instructions for replacing glass door. WARNING: Do not operate fireplace with the glass door unlatched, removed, cracked or broken. pilot and burners • Remove ember material before cleaning burners and replace when cleaning is complete. • Burner and controls should be cleaned with compressed air to remove dust, dirt or lint. • Use a vacuum cleaner or small, soft bristled brush to remove excess dust, dirt or lint. logs • If you remove logs for cleaning, refer to Installing Logs, Lava Rock and Glowing Embers, page 30, to properly replace logs. • Use a vacuum cleaner to remove any carbon buildup on logs. • Replace log(s) if broken. See Replacement Parts on page 44. • Replace ember material periodically as needed. See Replacement Parts on page 44. venting system Conduct annual inspection of the venting system following these guidelines: 1. Check areas of venting system that are exposed to the weather for corrosion (rust spots or streaks and, in extreme cases, holes). Have these items replaced immediately by a qualified service person. 2. Remove the vent cap and shine a flashlight into the vent. Remove any foreign material. 3. Check for evidence of excessive condensation. Continuous condensation can cause corrosion of caps,...
Эта инструкция также подходит к моделям:Камины - (V)CD36RNE (3.69 mb)
Камины - (V)CD36RP (3.69 mb)
Камины - (V)CD36RPE (3.69 mb)
Камины - (V)CD36TN (3.69 mb)