Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Electrolux, модель 3245

Производитель: Electrolux
Размер: 2.42 mb
Название файла:
Язык инструкции:
Перейти к скачиванию



Фрагмент инструкции


Burner Cap Burner Extra Large "POWER" Burner Head Left Rear (9,500 (12,200 BTU or )Gas Opening 14,200 BTU) Left Front Center Gas Opening Gas Opening _a nner & Outer Burner Caps I Burner Head (18,000 BTU) Right Front Gas OpeningS/ _, _, _. Right Front Gas Opening Dual Burner _ on Models 790.3248 "_790.3249 only Burner Skirt 36" Models only Burner Cap (Standard) Models only Burner Cap _Burner Head (5,000 BTU) Right Rear Gas Opening Burner Head (16,200 BTU) Right Front Opening Figure 1 Burner G rate Burner Cap Burner Head Electrode must be located properly in slot of each Burner Head Figure 2 Assembly of the Surface Burner Heads, Burner Caps, Burner Grates It is very important to make sure that all of the Surface Burner Heads, Surface Burner Caps and Surface Burner Grates are installed correctly and at the correct locations. 1. Place all 4 (four) or 5 (five) Burner Heads in the correct locations (See Figure 1). Make sure that the correct Burner Head is placed with the corresponding Gas opening and that the Electrode is located properly in the slot of each Burner Head (See Figure 2). Proper Burner Head placement insures that each Burner will have the correct spark required for surface gas ignition. 2. Place the correct Burner Caps at each of the burner locations. Each of the Burner Heads MUST have a Burner Cap installed to insure proper ignition and gas flame size (See Figure 2). 3. Place the 2 (two) or 3 (three) cast iron Burner Grates supplied with the range. Carefully lift the burners grates on to the cooktop over the burners. Properly installed Burner Grates will rest with all Grate legs on the cooktop. REMEMBER --DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE GAS OPENING. Always keep the Burner Caps and Burner Heads in place whenever the surface burners are in use. 7 Setting Surface Controls Dual Burner Head Assembly (present on Models 790.3248 & 790.3249 only) Step 4 Make sure that the Burner Head, Burner Caps and Burner Skirt are installed properly and at the correct locations. Burner Outer 1. Follow the Installation Instructions before installing and using your new Cap Hole Step 3 range. 2. Remove all packing tape from cooktop and the dual burner. Burner / 3. Discard all packing material located under all Burners (if applicable). / Skirt "., 4. To install Burner Head, Caps & Skirt, refer to figure 1 and follow the Burner following steps: Burner Headpin E_ i__ -I_ Head Step 1:Align Burner Head Pin A on Burner Base Hole. PinA Step 2: Place Burner Skirt around Head and Base. Step 3: Align out Burner Outer Cap Hole into Burner Head Pin B. Burner Head o_ Step 2 Step 4: Place Inner Burner Cap centered on Burner Base. Burner 5. Put back the grates on the cooktop. Base REMEMBER--DO NO...

Эта инструкция также подходит к моделям:
Варочные панели - 3244 (2.42 mb)
Варочные панели - 3249 (2.42 mb)
Варочные панели - 3248 (2.42 mb)
Варочные панели - 3244 (2.42 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории