Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Using Your Hob Choosing the power setting Touch the symbol corresponding to the chosen control levels. Stop NOTE: zone, and the display will incr when the desir ou can go directly to level if you so wish. To turn down the heat, press the key. To turn off the cooking zones press the lower and top parts of the key simultaneously, the power will reduce to zero and the temperature indicator will turn off OR press the key and the cooking zone power will decrease gradually, as will the temperature indicator, until they both turn off. While the cooking zones are still hot (temperatures exceeding 60°C), the residual heat indicator, adjacent to the cooking zone, will be lit. However, care should continue to be taken as the hob may still be hot to touch, even when the residual heat indicator is extinguished. WARNING: If a power cut occurs at any time, the hob will return to its previous state when power is restored. If all cooking zones were on maximum when power failed, they will be set at maximum when the power returns to the hob. To prevent this, should a power cut occur, switch off the hob at the mains wall switch. Using Your Hob Blinking temperature indicators The temperature indicators will blink if: -An object (eg. saucepan/lid) is placed on the cooking zone for more than 10 seconds. -Any boiled over liquids or food are spilled onto the control zone. -Any extended pressure is placed on the control zone. These could cause the word ‘DEF’ to appear on the display, accompanied by a beep. The temperature indicators will blink and the cooking zone(s) in use will turn off. To stop the beep, remove the cause of the malfunction. To stop the temperature indicators blinking, press the key for 3 seconds and the control zone(s) can be used again. Safety cut out If the user inadvertently forgets to turn off one or more cooking zones, the corresponding control is automatically put out of order after a given amount of time. Power Level Maximum Operation Time 1 - 2 6 hours 3 - 4 - 5 5 hours 6 - 7 - 8 4 hours 9 - 10 - 11 3 hours 12 - 13 - 14 1.5 hours Using Your Hob Overheating Prolonged use of the hob could cause the electronic components to overheat. A thermal protection device momentarily sets a reduced power (level 3) on the right hand cooking zones. The temperature indicators blink to show you that this safety measure has been taken. When the temperature returns to normal, the temperature indicators stop blinking and the cooking zones can once again be used at higher power levels if required. Should the temperature of the electronic components continue to rise, the cooking zones are locked until the temperature drops - as indicated by the blinking of the 3 points on each of the four temperature indicators. Cooking time programming You can programme the cooking zones seperately or simultaneously and for different cooking times of up to 3 hours. Once you have selected the heating power, programme the cooking time as follows: . Press the Timer key for the cooking zone (the corresponding indicator light blinks), 0.00 is displayed. The cooking time is adjusted in steps of 10 seconds for the first 9mins 50 secs, then in steps of 1 minute from 10mins to 3 hours. . Press the cooking zones + key until you reach the desired cooking time. The time is displayed in hours and minutes for periods above ten minutes, and minutes and seconds for periods below ten minutes. . Confirm the programmed setting by pressing the Timer key once more (the corresponding indicator light stays on), the countdown begins immediately until the end of cooking. The countdown is displayed minute by minute from 3 hours to 10 minutes, and second by second from 9 minutes 59 seconds to 0. You can programme all the cooking zones for different cooking times. The countdown displayed corresponds to the zone with the fixed indicator light. If another zone has been programmed, simply press the corresponding Timer key to display that zones countdown. Once the time is up, the power to the cooking zone is automatically turned off, the temperature indicator goes back down to 0. A beep sounds to indicate that cooking is done, to stop the beep, simply press the Timer key . The countdown for the other programmed cooking zone is then displayed. Using Your Hob In the unlikely event of a crack (no matter what size) appearing in the ceramic surface switch off the electricity supply to the appliance IMMEDIATELY and contact your Service Centre. DO NOT USE THE APPLIANCE UNTIL IT IS REPAIRED! Do not leave a hotplate turned on when you are not cooking as this makes it harder to clean the ceramic surface. Temperature cut-outs are built into the hob elements to protect them from over heating. After several minutes with the control setting on FULL the temperature cut-out switches the element OFF and ON continuously. This protects the hob element against the build-up of excessive heat in the cooking area. Care should be taken when using any pans on a ceramic surface not to drag and cause s...