Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
The heater element may or may not be on, depending on the thermostat control setting (SEE “HEATER THERMOSTAT CONTROL”). RESETTING THE TEMPERATURE CUTOFF SWITCH Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset. It can be reset by switching the MAIN ON/OFF SWITCH to OFF and waiting 5 minutes before switching the unit back on. CAUTION If you need to continuously reset the heater, unplug the unit and call Dimplex North America Limited at 1-800-668-6663. REMOTE CONTROL The fireplace is supplied with an integrated on/off remote control. Note: Ensure that the fireplace 3 position switch is set to the remote control setting. To operate, push the ON button to turn fireplace on, push the OFF button to turn the fireplace off. BATTERY REPLACEMENT To replace the battery, slide battery cover open on the hand held transmitter. Correctly install one 12 volt (A23) battery in the battery holder. Close the batter cover. MAINTENANCE WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. LIGHT BULB REPLACEMENT Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental burning of skin. Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears. There are two bulbs under the log set which generate the flames and embers. BATTERY COVER BATTERY 4 A B C TOOL REQUIREMENTS Phillips screw driver HELPFUL HINTS It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace light bulbs. UPPER LIGHT BULB REQUIREMENTS Quantity of 1 clear chandelier or candelabra bulbs with an E-12 (small) socket base, 7 watt rating. UPPER BULB REPLACEMENT 1. Open door by pulling the handle. 2. Locate the upper bulb bracket. 3. Bend light retainer bracket down. 4. Locate and remove the light bulb. 5. Insert new bulb. 6. Bend light retainer bracket back into its original position. 7. Close the door. LOWER LIGHT BULB REQUIREMENTS Quantity of 2 clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60 watt rating. LOWER BULB REPLACEMENT 1. Open door by pulling the handle. 2. Remove the screw from the logset located in the center of the emberbed and remove the logset from the unit. 3. Locate and examine the bulbs to determine which bulb(s) required replacement. 4. Locate and remove the light bulb(s). 5. Insert new bulb(s). 6. Install the logset into the unit, pushing firmly against the glass. Replace the logset retaining screw into the ember bed. 7. Close the door. 5 GLASS CLEANING The clear door is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the clear door may collect dust particles, these can be removed by dusting lightly with a clean dry cloth. To remove fingerprints or other marks, the clear door can be cleaned with a damp cloth. The clear door should be completely dried with a lint free cloth to prevent water spots. To prevent scratching, do not use abrasive cleaners or spray liquids on the clear door surface. PLASTIC DOOR CLEANING To remove fingerprints or other marks, the clear door can be cleaned with a damp cloth. The clear door should be completely dried with a lint free cloth to prevent water spots. To prevent scratching, do not use abrasive cleaners or spray liquids on the clear door surface. BRASS DOOR CLEANING To remove fingerprints or other marks, the clear door can be cleaned with a damp cloth. The clear door should be completely dried with a lint free cloth to prevent water spots. To prevent scratching, do not use abrasive cleaners or spray liquids on the clear door surface. NICKEL DOOR CLEANING To remove fingerprints or other marks, the clear door can be cleaned with a damp cloth. The clear door should be completely dried with a lint free cloth to prevent water spots. To prevent scratching, do not use abrasive cleaners or spray liquids on the clear door surface. STOVE SURFACE CLEANING Use warm water only to clean painted surfaces of the Compact Stove. Do not use abrasive cleaners. SERVICING Except for light bulb replacement and cleaning described above, an authorized service representative should perform any other servicing. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN NO USER-SERVICEABLE PARTS INSIDE ONE YEAR LIMITED WARRANTY Products to which this limited warranty applies This limited warranty applies to the following models of your newly purchased Dimplex electric stove DS5598, SS5800PB, DS5804 and to newly purchased Dimplex fireplace surrounds (mantels) and trims. This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA (and the District of Columbia) except f...