HAAN® Corporation assumes no responsibility for any errors that may appear in this document nor does it make expressed or implied warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. HAAN® Corporation shall not be liable for incidental or consequential damages in connection with or arising out of the furnishing, performance, or use of this document and the program materials that it descri

HAAN® Corporation assumes no responsibility for any errors that may appear in this document nor does it make expressed or implied warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. HAAN® Corporation shall not be liable for incidental or consequential damages in connection with or arising out of the furnishing, performance, or use of this document and the program materials that it descri

GE Energy Oil & Gas Business has long-standing experience in manufacturing gas turbines dating back to 1961 when a manufacturing agreement was established with General Electric (U.S.A.) to complement the existing portfolio of products for the petroleum and petrochemical industries (reciprocating and centrifugal compressors, gas engines, pumps, valves, etc.). A proven combination of sound design and quality assurance techniques places these gas turbines among the world’s most reliable. Basic mode

Never use steam head in a horizontal position or tilt into a backward position, this may result in hot water discharge. 10. To reduce the risk of electric shock, do not immerse the appliance in water or other liquids. 11 Appliance should always be turned off before plugging or unplugging. Never yank the cord to disconnect from outlet, instead grasp plug and pull to disconnect. 12. Do not allow cord to touch hot surfaces. Let appliance cool completely before putting away. 13. Loop cord loosel

Never yank the cord to disconnect from outlet, instead grasp plug and pull to disconnect. 12. Do not allow cord to touch hot surfaces. Let appliance cool completely before putting away. 13. Loop cord loosely under the appliance when storing. 14. Do not let power cord contact sharp edges or hot surfaces. 15. Do not try to fasten the nozzle hose guide during operation. Scaktag may occur if the nozzle hose guide is removed while using the appliance. 16. ASvays disconnect appliance from e*ectnc

Prepare the waffle batter well in advance ( Recipes). Warning! Do not operate appliance with a damaged cord or plug, or after the appliance malfunctions or has been dropped or damaged in any manner. Call our toll-free customer assistance number for information on examination, repair, or adjustment. Warning! Unplug from outlet when not in use and before cleaning. Baking waffles • Fill the measuring cup (13) to the 5oz. mark with batter. Pour and spread the batter evenly on the lower waffle plate

4. Before each use, inspect the cord for cuts and/or abrasion marks. If any are found, this indicates that the appliance should be serviced and the cord replaced. 5. Never wrap the cord tightly around the appliance, as this could place undue stress on the cord where it enters the appliance and cause it to fray and break. PARTS 3 2 1 4 5 6 Top of Lid 1. Lid Latch 2. Lid 3. Grids 4. Variable Temperature Control (MIN–MAX) 5. Power ON Light 6. Preheat Light 3 840176200 Ev04 5/28/08 2:37 PM Page 4 OP

Turn iron upside down until Water Tank Opening is parallel with sink. Water will run out of water tank opening. 2. After iron has completely cooled, fully retract cord into iron and store in an upright position. Do not store iron laying flat on soleplate. Soleplate 1. Never iron over zippers, pins, metal rivets, or snaps, as these may scratch the soleplate. 2. To clean occasional build-up on the soleplate, wipe with a sudsy cloth. Do not use abrasive cleansers or metal scouring pads. 3. Always s

When the steaming stops is also an indicator that the waffle is done. Cleaning Your Waffle Baker 1. Unplug from outlet and let cool. 2. Wipe cooking grids and outside of unit with a damp, soapy cloth. Rinse cloth and wipe grids again. 3. Do not use steel wool, scouring pads, or abrasive cleansers on any part of the unit. Never use sharp or pointed objects for cleaning purposes. 4. Always allow the appliance to cool down completely before storing. The unit can be stored upright to save space. DO

2 Optional Features.................................... 5 Parts and Features.................................. 3 Caring for Your Iron ................................ 6 Using Your Iron........................................ 4 Troubleshooting...................................... 7 Fabric Setting Chart ................................ 5 Customer Assistance ............................ 8 We invite you to carefully read this instruction manual before using your appliance. For Customer Assistance i