Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Your new SF-407 Fabric Steamer is now fully assembled and ready for use. Please continue reading this manual for instructions on using the Fabric Steamer, as well as directions for cleaning and storage. FIGURE 9 Top Innovations, Inc. USING THE FABRIC STEAMER FILLING WATER TANK AND WATER RESERVOIR IMPORTANT: Always make sure that Lighted On/Off Switch is set to “Off” position and unit is unplugged before attempting to fill Water Tank 1. Remove Water Tank from main unit. 2. Holding Water Tank upside-down, unscrew and remove Valve Cap by rotating it in a counter-clockwise direction (FIGURE 10). 3. Fill Water Tank with water through Valve Cap Hole. Refer to guidelines on left side of Water Tank to fill it with correct amount of water, depending on desired steam time (15, 30, or 45 minutes). Do not exceed 45 MIN (40 oz.) mark. NOTE: To prolong life of unit, it is recommended that you use distilled or demineralized water in Water Tank. Do not attempt to substitute another water tank for the one designed for use with this unit. 4. Replace Valve Cap by rotating it in a clockwise direction. 5. Place Water Tank back onto main unit (FIGURE 11). The sound of water flowing from Water Tank into Water Reservoir should be audible for a short period of time. IMPORTANT: Do not attempt to operate Fabric Steamer with an empty Water Tank, as doing so could result in damage to the unit. FIGURE 10 FIGURE 11 Top Innovations, Inc. USING THE FABRIC STEAMER OPERATING THE FABRIC STEAMER 1. Make sure that Water Tank is filled with water and placed correctly onto main unit, and that Fabric Brush is securely attached if you wish to use it. 2. Plug power cord into a convenient 3-prong electrical outlet (FIGURE 12). 3. Switch Lighted On/Off Switch to “On” position (FIGURE 13). 4. Unit requires approximately 35-40 seconds for boiler to heat. Once it has heated, Fabric Steamer will begin producing a flow of steam. NOTE: It is common for unit to produce gurgling sounds and small amounts of water during the first few minutes of steaming. This is a natural part of the steaming process. Pointing Steam Nozzle towards the ground and shaking it gently may help to remove excess water from Steam Hose more quickly (FIGURE 14). 5. Once steam flow is steady and excess water has been removed from Steam Hose, you may proceed with your steaming tasks. Refer to Tips for Using the Fabric Steamer guide on page 12 of this manual for more information about steaming garments and other fabrics. 6. When you have completed your steaming tasks, immediately switch Lighted On/Off Switch to “Off” position and unplug power cord from electrical outlet. Refer to Proper Storage section on page 13 of this manual for information on proper cleaning and storage of Fabric Steamer. FIGURE 12 FIGURE 13 FIGURE 14 Top Innovations, Inc. USING THE FABRIC STEAMER TIPS FOR USING THE FABRIC STEAMER STEAMING GARMENTS 1. Place garment on a clean, rust-free clothes hanger. 2. Place hanger (with garment) on Clothes Hanger Hook (FIGURE 15). CAUTION: Use care when handling garments on the Clothes Hanger Hook. Pulling on the garment with too much force may cause the unit to tip over. 3. Grasp Handle, and direct Steam Nozzle towards bottom of garment. Steam will rise along inside and outside of fabric, removing wrinkles. Slowly slide Steam Nozzle vertically, from bottom to top of garment (FIGURE 16). NOTE: Do not allow kinks to form in hose at any time during use. 4. Direct Steam Nozzle away from garment and smooth fabric with your free hand. 5. Repeat steps 3 and 4 as necessary until fabric is smooth and wrinkle free. FIGURE 15 FIGURE 16 OTHER STEAMING TIPS -Curtains and draperies may be steamed while still hanging. -To remove wrinkles from towels, handkerchiefs and napkins, drape them over a rod or towel rack and gently steam them. -Heavier fabrics may require repeated steaming to effectively remove wrinkles. -To remove exceptionally stubborn wrinkles steam both sides of fabric. -For additional assistance in removing tough wrinkles, or to remove lint and other particles, attach Fabric Brush to Steam Nozzle (see Attaching the Fabric Brush section on page 8 of this manual). -Use Press Pad in order to steam difficult spots and edges and to create creases in fabric. Slide your hand through the velcro strap on back of Press Pad to secure it to your hand. This will protect your hand from the flow of hot steam. Then steam fabric while pressing it firmly but gently against the Press Pad. Top Innovations, Inc. CARE AND STORAGE GUIDELINES PROPER STORAGE Preparing your Fabric Steamer for storage is quick and simple. When you have finished your steaming tasks, follow the steps listed below. 1. Set On/Off Switch to “Off” position, and unplug grounded power cord from electrical outlet. 2. Allow unit to cool completely. 3. Remove Water Tank from unit and unscrew Valve Cap to drain remaining water into sink or tub. 4. Remove Drain Plug and drain any remaining water in Water Reservoir into a sink or tub to pr...
Эта инструкция также подходит к моделям:Утюги - SF-407 (239.37 kb)