Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
The “OFF / AUTO OFF” light will flash when: • The electrical plug is inserted into the electrical outlet. • The temperature is set to “OFF”. • The auto-shutoff function is activated. • If the iron is left on the cradle with the power still on, it will automatically shut off after approximately 10 minutes. The “Auto off” light will illuminate. Press this button firmly, once the iron has been placed on the cradle. • Each time this button is pressed, the flashing light will cycle to the next temperature indicator, in the order shown by the arrows in the diagram. • In order to avoid a malfunction caused by accidental button contact, the iron has been designed so that the activation of the temperature control button requires additional pressure. 1 3 2 4 Temperature Control Button Off/Auto Off Light Temperature Indicator Lights Burst of Steam Button Steam Button Spray Button Ready Light • Pressing this button will discharge a powerful shot of steam. • This light will illuminate when the appropriate operating temperature is reached. • During ironing, the ready light will begin to flash whenever the temperature of the iron starts to decrease. If the temperature continues to decrease, the light will eventually turn off. When the light begins to flash, place the iron back on the cradle for reheating. Once the soleplate heats up to the appropriate operating temperature, the light will again illuminate. • The selected light will continue flashing until the preset temperature is reached. • Once the preset temperature is reached, the light will stop flashing and remain illuminated. • If the iron is not on the cradle, these lights will not be illuminated. • Leave button up for steam, press down for a dry iron. • Pressing this button will discharge a mist of water from the spray nozzle. The “OFF / AUTO OFF” light will flash when: • The electrical plug is inserted into the electrical outlet. • The temperature is set to “OFF”. • The auto-shutoff function is activated. • If the iron is left on the cradle with the power still on, it will automatically shut off after approximately 10 minutes. The “Auto off” light will illuminate. Press this button firmly, once the iron has been placed on the cradle. • Each time this button is pressed, the flashing light will cycle to the next temperature indicator, in the order shown by the arrows in the diagram. • In order to avoid a malfunction caused by accidental button contact, the iron has been designed so that the activation of the temperature control button requires additional pressure. FEATURES How does a cordless iron work? • The iron rests on a cradle that supplies the power to heat the iron. • Each time you set aside the iron to adjust a garment on the ironing board, the iron should be placed back on the cradle. This will allow the iron to quickly “heat” so the temperature of the iron remains at the desired level. FULL indicator Spray nozzle Anti-drip Control Iron Cradle Case Tank Red tape Lock/Release button SoleplateHandle Temperature control Case latch Controls Cord (cord reel) Electrical plug If the temperature of the soleplate decreases significantly during iron usage, this function will be activated to stop the production of steam. Press this button to remove the water tank. Do not over-extend the cord by pulling it farther than the section marked by this red tape. Lid for water inlet /outlet spout. This lid prevents debris from entering the spout. How does a cordless iron work? • The iron rests on a cradle that supplies the power to heat the iron. • Each time you set aside the iron to adjust a garment on the ironing board, the iron should be placed back on the cradle. This will allow the iron to quickly “heat” so the temperature of the iron remains at the desired level. FULL indicator Spray nozzle Anti-drip Control Iron Cradle Case Tank Red tape Lock/Release button SoleplateHandle Temperature control Case latch Controls Cord (cord reel) Electrical plug If the temperature of the soleplate decreases significantly during iron usage, this function will be activated to stop the production of steam. Press this button to remove the water tank. Do not over-extend the cord by pulling it farther than the section marked by this red tape. Lid for water inlet /outlet spout. This lid prevents debris from entering the spout. PREPARING TO IRON 1 Preparation 1. Remove the case. 2. Pull the electrical cord out only to the length required. Insert the plug all the way into an electrical outlet. 120 V AC Red tape • Do not over-extend the cord farther than the section marked by this red tape. 2 Filling with Water It is not necessary to pour water into the water tank if not using steam or water spray features. 1. Press down the steam button to set the iron to the “Dry” position. 2. Remove the tank and fill it with water, up to the mark indicating “FULL”. While pressing down the release button, remove the tank. Fill with tap water • Regions that have extremely hard water should use a mixture of 50% ...
Эта инструкция также подходит к моделям:Утюги - MLI7500AAW (1.73 mb)
Утюги - MLI7500AAW (1.73 mb)
Утюги - MLI7500AAW (1.73 mb)
Утюги - MLI7500AAW (1.73 mb)