Оценок - 5, средний балл: 3.4
(
)
)
|
Фрагмент инструкции
10-Iron stand 11-Insulating ironing mat • To change the setting from “Min” to “Max”, turn the thermostat control anti-clockwise. • Set the thermostat control (D) according to the table below. • The thermostat indicator light will come on (E). It goes out when the soleplate has reached the required temperature. • Position the iron stand, ideally on the corner of the mat (A). During any pause in ironing, always put your iron on its stand, never leave it on its soleplate on the mat. English047256 - 13/05Please read these instructions carefully and keep them to hand MINUTEWhat water to use? Your appliance has been designed to function with untreated tap water. However, it is necessary to operate the Self-Clean function regularly in order to eliminate hard water deposits from the steam chamber. If your water is very hard (check with your local water authority), it is possible to mix tap water with store-bought distilled or demineralised water in the following proportions : -50% untreated tap water, - 50% distilled or demineralised water. Types of water not to use ? Heat concentrates the elements contained in water during evaporation.The types of water listed below contain organic waste or mineral elements that can cause spitting, brown stai- ning, or premature wear of the appliance: water from clothes dryers, scented or softened water, water from refrigerators, batteries or air conditioners, pure distilled or demineralised water or rain water should not be used in your Tefal iron. Also do not use boiled, filtered or bottled water. Important! Before using your iron for the first time on the steam setting, we recommend that you let it operate for a few seconds holding it horizontal and away from your ironing. On first use you may notice a small amount of smoke.This is normal and will disappear. Important! Remove any labels from the soleplate before heating the iron. You have just purchased the first instant ironing kit ever invented.This is a new, ultra- compact iron concept which can be used anywhere, thanks to its insulating ironing mat and its compact iron stand.The "instant" iron is designed for short, everyday ironing sessions. I. IRONING • This ironing mat is extra-large, heat and steam resistant. It allows you to iron on any suitable flat surface without risk of scorching or dripping. With its rectangular shape, the mat enables perfect ironing to be carried out on the corner of a suitable heat-resistant table. It may be creased after being stored in the box. Just iron it before beginning your session. Creases will disappear in a flash. • To do some ironing, place your ironing mat on a suitable flat, stable, heat-resistant surface (A). Using the mat Installing the iron stand • Unplug your iron before filling it. • Press on the Dry / Steam control so that it is set to DRY (B) and will not drip during filling. • Place the iron flat on its mat, lift the filler cap and fill it to the "max" mark indicated (capacity, 125 cc). or • With the iron set on its base, open the filler cap and fill it without exceeding the "MAX" mark indicated on the side of the tank (C). NOTE : Reduce the water flow towards the end of filling in order to avoid any overflow. • Close the filler cap.You can now plug in your iron. Filling the tank Adjusting the temperature A B C D E • SELF-CLEANING PROCEDURE To extend the working life of your iron, carry out the self-cleaning procedure once a month. - Leave the iron with the water, tank full, on its stand (thermostat set at maximum). -When the indicator light goes out, unplug the iron and hold it over a sink. - Remove the anti-scale valve. - Shake the iron gently, holding it horizontally, over the sink, until most of the water, (with the impurities) has run out through the soleplate. - Re-insert the anti-scale insert. - Place the iron on its stand and plug in for 2 minutes to dry the soleplate. - Unplug the iron and, when the soleplate has cooled, wipe it with a soft cloth. • CLEANING THE SOLEPLATE -While the soleplate is still slightly warm, clean it by wiping over it with a damp, non-metallic cloth. • SOFT IRONING MAT -The mat can be cleaned by wiping over it with a damp sponge. - Note: the mat cannot be cleaned in a washing machine. Machine washing will damage it, making it unsuitable for ironing. - Do not dry clean. 4 IF THERE IS A PROBLEM Problem Possible causes Solutions • Water is running out of the steam holes in the soleplate. • Brown deposits are coming out of the soleplate and staining the ironing. • The soleplate is brown or dirty and can stain the ironing. • Your iron produces little or no steam. • The soleplate is scratched or worn. • Water flows out of the tank hatch. • The iron steams at the end of tank filling. • At the end of ironing, there is an accumu- lation of water in the bottom of the iron stand. • The selected temperature is too low for steam. • You are using steam when the iron is not hot enough. • You have stored your iron flat, without setting the control to dry. •...