Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
Cords rated for less amperage may overheat. Use care to arrange the cord so that it cannot be pulled or tripped over. 13. WARNING: Never fill the iron with fabric conditioner, starches or any other solution, as these will damage the steam mechanism. Do not use contaminated water. 14. CAUTION! TO AVOID FIRE, never leave iron unattended while it is plugged in. 15. CAUTION! TO PREVENT ELECTRIC SHOCK, never use the iron in a location where it can fall or be pulled into water or another liquid. If the iron falls into water or other liquid, unplug it immediately. DO NOT reach into the water or liquid. 16. WARNING: Never use scouring pads, abrasive or chemical cleaners, or solvents to clean the exterior or soleplate of your iron. Doing so will scratch and/ or damage the surface. 17. CAUTION! DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur. 18. Always store your iron standing upright, not on the soleplate. If stored face down, even the smallest amount of moisture will cause the soleplate to corrode and stain. 19. This appliance is for household use only. GETTING TO KNOW YOUR IRON 2 1. Blast Of Steam 2. Spray Button 3. Variable Steam Control 4. Water Inlet With Cover 5. Spray Nozzle 6. Temperature Control Dial 7. Water Level Window 8. Stainless Steel Soleplate 9. Temperature Ready Light/ Auto Shut-Off Light 10. Comfort Grip Handle 11. Power Cord 12. Water Flask TROUBLESHOOTING 9 Technical Specifications Voltage: 120V, 60 Hz Power: 1600 Watts *Illustrations may differ from actual product Before using your Steam Iron, remove any labels, stickers or tags that may be attached to the body or soleplate of the iron.When turned on for the first time, your new iron may emit an odor for up to 10 minutes. This is due to the initial heating of the materials used in making the iron. The odor is safe and should not reoccur after initial heating. Also, before ironing with steam for the first time, allow iron to heat, hold in a horizontal position and hit the blast of steam button several times. The iron may emit some small particles from the steam holes. This is normal and will clear after pressing the blast of steam button several times. 12 PROBLEMPOSSIBLE REASONS & SOLUTIONSIron does not heatThermostat ready lightgoes On and OffSome odor or small particles come out of steam vents of new ironIron does not steamWater droplets comingfrom steam vents• Iron should be plugged into a 120V AC electrical outlet only. Make sure that the plug is securely in the socket. • Temperature setting too low. Turn to higher setting. • This is normal. The light goes On and Off as the thermostat is switching the heating element On and Off to maintain the selected temperature. • This is normal. Follow instructions for first use and allow iron to steam through 2- 3 fillings & press the steam burst button occasionally to eliminate small white particles. • Water tank may be empty or water level is very low. Add water. • Make sure that the temperature control dial and the variable steam control are correctly set. Formaximum steam, (setting " Max" on steam control), temperature control dial should be set on "• •• ". • Adjustable steam control is set on " 0". Always allow the iron to reach the selected temperature with the adjustable steam control setting at "0". Make sure the temperature control dial is set in the correct steam area, e.g. " • ", and the steam control is noton "0". For more steam, turn temperature dial to higher setting, e.g. "• •• ", and the steam control to "Max". • If temperature setting and steam control setting arecorrect and there is no steam, gentlytap the soleplate on the ironing board a few times. Movethe variable steam control from "0" to "Max" a fewtimes. • Iron may not be hot enough. Set thermostat to the"Max" position. Always allow iron sufficient time toheat up (thermostat light goes off) before activating the variable steam control. • Overuse of steam burst. Allow more time betweeneach burst. • Iron may have been overfilled. Turn iron off,emptywater and follow instructions for filling. • Iron may be set to “Self Clean” mode. • Steam performance may be low if iron requires seasoning. To season, use regular tap water for 1or 2 tanks until steam improves. FEATURES OF STEAM IRON 3 1. BLAST OF STEAM The Blast of Steam provides extra, sudden blasts of steam which aid in removing stubborn wrinkles from fabrics such as denim, cotton or linen. 2. ATOMIZERSPRAY BUTTON Pressing this Button provides a defined jet of spray which gently moistens fabric. 5. WATER FILLING INLET The cover prevents dust and foreign matter from entering the water tank. It also stops any water from spilling during ironing. 3. VARIABLE STEAM CONTROL Minimum to maximum steaming for different materials. Self cleaning feature flushes internal sole plate with water. 7. STAINLESS STEEL SOLEPLATE Provides maximum glide- ability and heat retention. 4. TEMPERATURE CONTROL Turn dial to select tempe...