Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
(3) LED indicator There are 2 LED's build into the tablet. These LED's indicate current condition of the tablet. - Bluetooth mode 1. When tablet is turned on, 2 LED's will flash once. 2. When the battery power is low, the red LED will be solid. In this case, please change the batteries. 2-2 English StarBoard BT-2G -2G Usage Procedures 3. The blue LED will blink continuously during connecting to PC. 4. The blue LED will be solid when the pen is detected within active area. - USB mode 1. When USB cable is initially connected to the tablet, the red LED will flash once and the blue LED will blink continuously. 2. The blue LED will be solid when the pen is detected within active area. Condition Bluetooth Mode USB Mode Blue LED Red LED Blue LED Red LED Power on Flash once Flash once USB cable plugged Blink continuously Flash once Connecting Blink continuously Off Blink continuously Off Pen tip on active area of the tablet Off Off Off Off Pen within active area (not touched) Solid Off Solid Off Low battery Off Solid . 2.2 Using the Stylus Pen This section describes how to use the StarBoard stylus pen. 2.2.1 How to use Stylus Pen The stylus pen has a ON/OFF switch. Battery life can be prolonged by ON/OFF the switch. To use the stylus pen, set the power switch of the stylus pen to the ON position. ON/OFF switch 2-3 English StarBoard BT-2G -2G Usage Procedures 2.2.2 Basic Stylus Pen Operations The stylus pen can be used in the same way as a mouse. Under the stylus pen’s default settings, the pen tip button is set to correspond to the left mouse button. When Windows is open, the pen tip button may be used to perform the following mouse actions. .Clicking Press the pen tip against the tablet operating area with a suitable amount of force and then release it quickly. .Double-clicking Press the pen tip against the tablet operating area with a suitable amount of force and then release it, two times in a row. .Dragging Press the pen tip against the tablet operating area with a suitable amount of force and then move the pen while keeping it pressed against the tablet operating area (without releasing it from the tablet operating area). The permitted stylus pen input angle range is 30° in any direction from a position where the stylus pen is perpendicular to the tablet operating area. Note that if the pen is tilted at an angle greater than 30°, its coordinates may not be input correctly. 2.2.3 Stylus Pen Settings The stylus pen has one pen tip button, and two side buttons. Mouse actions can be assigned to these three buttons. The default button settings are summarized in the following table. Button User action Corresponding mouse action Pen tip Press the pen tip against the tablet operating area Mouse left-click Side Button No.0 Press the button with the pen tip slightly removed from the tablet operating area (5 mm or less) Mouse left double-click Side Button No.1 Same as above Mouse right-click Pen tip Side Button No.1 Side Button No.0 2-4 English StarBoard BT-2G -2G Usage Procedures 2.2.4 Changing the battery in the stylus pen The stylus pen contains a single AAA alkaline battery. If the pen begins to operate erratically (e.g., if pen input is cut off), change the battery as described below. Note that battery life is approximately 1800 hours under normal usage. (1) Turn the stylus pen grip to separate the two halves. (2) Remove the AAA alkaline battery contained in the grip, and insert a new cell with the positive side facing the pen tip. + - (3) Put the stylus pen back together. +- CAUTION When changing the battery, be careful not to close the pen’s rear part too forcefully. If too much force is applied when closing the rear part of the stylus pen, the pen may be damaged. 2-5 English StarBoard BT-2G -2G Usage Procedures 2.2.5 Replacing the Stylus Pen Tip When the stylus pen tip wears down and becomes too short, replace it as described below. (1) Using the special pin set, remove the stylus pen tip. (2) Insert a new pen tip into the stylus pen. 2-6 English StarBoard BT-2G -2G Setup Software 3. Setup Software Before starting installation, tablet and stylus pen needs to be ready. (1) Insert batteries to the tablet and the stylus pen. (2) Power on the stylus pen. (3) Power on the tablet and keep pressing the "disconnect" button 5seconds or longer. Keep pressing 5seconds or longer. 3.1 Install Bluetooth tablet manager (1) Insert "StarBoard BT-2G Setup Software" CD to PC. (2) After the menu appears, click "Bluetooth Pen Pad Driver". and tablet manager will be installed automatically. (3) Start "Bluetooth Pen Pad" automatically. Click "Next". Then, Bluetooth/USB tablet manager will be installed. (4) After installation, CD will be ejected. 3-1 English StarBoard BT-2G -2G Setup Software 3.2 Install WIDCOMM Bluetooth Software (1) Insert "StarBoard BT-2G Setup Software" CD to PC again. (2) Click "Bluetooth Dongle Driver" and install WIDCOMM Bluetooth Software. (3) Start "WIDCOMM Bluetooth Software" automatically. Click "Next". (4) L...
Эта инструкция также подходит к моделям:Устройства ввода - StarBoard BT-2G (8.73 mb)