Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Read the instructions before use. This appliance must be installed inaccordance with such regulations asare in force. Do not use the heater in an explosive atmosphere. Keep the heater away from areas where gasoline or other flammable liquids or vapors are stored. Prior to use, check for damaged parts such as hoses, regulators, pilot or burner. Disconnect LPG bottle before moving the heater. Do not attempt to alter unit in any manner. EXAMPLE: using the heater without the top canopy reflector or radiant screen. Do not shorten the burner post assembly. The appliance shall not be used in basements or below ground level. It must always be placed on a solid and level surface. Always assure there is ample fresh air ventilation. For outdoor use ONLY. Never replace or substitute the regulator with any regulator other than the factory suggested replacement. Do not clean the heater with cleaners that are combustible or corrosive. Do not paint radiant screen, control panel or top canopy reflector. All leak tests should be done with a soapy solution. NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS. The LP gas cylinder should be turned off when the heater is not in use. At least once a year, the unit should be inspected for the presence of spiders, spider webs or other insects. Check the heater immediately if any of the following exist: 1. The smell of gas in conjunction with extreme yellow colored tips of the burner flames. 2. The heater does not reach temperature. 3. The burner makes popping noise during use (a slight popping noise is normal when the burner is extinguished after using). The propane hose with regulator assembly shall be located out of pathways where people may trip over it or in areas where the hose will not be subject to accidental damage. Children and adults should be aware of the hazards of high surface temperature and shall stay away to avoid clothing burn or ignition. Young children should be carefully supervised when they are in the area of the heater. Clothing or other flammable material should not be hung from the heater, or placed on or near the heater. Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater. Installation and repair should be done by a qualified service person. The heater should be inspected before use and cleaning may be required at least once a year, or as necessary. It is imperative that control compartment, burner and circulating air passageways of the heater be kept clean. Keep the appliance area clear of combustible materials such as gasoline and other flammable vapors and liquids. Do not obstruct the flow of combustion and ventilation air. Keep the ventilation opening of the cylinder enclosure free and clear of debris. 4 ASSEMBLY FOR LIGHT SYSTEMASSEMBLY FOR LIGHT SYSTEM ASSEMBLY FOR LIGHT SYSTEMASSEMBLY FOR LIGHT SYSTEM WARNING: TO BE INSTALLED ONLY BY AN AUTHORISED PERSON Instruction For Battery Installing Upon first time use of the product,please remove the ignition button and install an AAA battery as indicated. Ignition button Control knob Replace Battery Ignition button AAA battery 5 ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 1 ----Attach Post to Gas Cylinder Housing Place the post on the top of the gas cylinder housing. Fasten the post to the gas cylinder housing using the four (4 pcs) M8 X35mm Bolts , 8mm Lock Washer , Nuts for M8 X35mm Bolts . Step 2 ----Attach Head Assembly to Post Slide the gas hose with the attached Head assembly through the top of the post and down through the hole in the top of the gas cylinder housing. Screw the combustion assembly on to the post, and tighten securely. Step 1 5 12 10 6 8 3 4 5 Step 2 6 ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 3 ----Attach Double Pointed Bolt to Head Assembly Attach double pointed bolts (3 pcs) and 6mm washers (3 pcs) to the top of head assembly and tighten the bolts securely. Step 4 ----Attach Center Reflector to Reflector Attach center reflector to the top of reflector (4 pcs) by M6 X 10 mm screws (12 pcs) , 6mm washers (12 pcs) and nuts (12 pcs). Step 3 9 13 3 Step 4 2 1 11 7 9 7 8 ASSEMBLY Step 5 3 Step 5 ---- Attach Center Reflector and Reflector Load center reflector and reflector to the top of head assembly by double pointed bolts (3 pcs) to the top of Head Assembly 6mm washers (3 pcs) and nuts (3 pcs) 7 9 13 NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 6 ---- Connect Gas Line to Cylinder Step 6 Attach Gas hose to regulator hose with 3/8 Inch Open End Wrench and Adjustable Wrench. Attach regulator to cylinder. Tighten securely. Move cylinder to the plate of base assembly. 4 14 15 SAFETY CHECKS SAFETY CHECKSSAFETY CHECKS NOTE: Always che...