Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
ESL E-Series
hp
e2400-FC 2Gb
Interface
StorageWorks
Controller
Upgrade
Caution: Parts can be damaged by
Caution: Before continuing with this
electrostatic discharge. Keep parts in their
procedure, ensure the following components
containers until needed. Ensure you are
are upgraded to the necessary firmware
properly grounded when touching static-
versions:
sensitive components.
• library: 1.02 or greater
• Interface Manager: I130 or greater
• Command View ESL: 1.3.00 or greater
Refer to the HP StorageWorks Interface
Manager and Command View User Guide
Note: This part is not hot-swappable.
It is necessary to power down the library
for detailed procedures on checking
to replace this part.
firmware revisions and making updates.
1
ESL E-Series
e2400-FC 2G
Interface
hp
Controller
StorageWorks
Upgrade
1
E
S
L E-Series
e2
400-FC 2G
I
n
t
erface
Controller
Caution: Parts can be damaged by
h
p
Up
grade
N
o
te: This part is not hot-swappable.
I
t
i
s
necessary to power down the library
St
orageWorks
t
o
r
eplace this part.
electrostatic discharge. Keep parts in their
C
a
ution: Parts can be damaged by
e
l
e
ctrostatic discharge. Keep parts in their
c
ontainers until needed. Ensure you are
properly grounded when touching static-
s
e
n
sitive components.
containers until needed. Ensure you are
1
N
o
te: The cable clamp provided is not
n
e
e
ded for this procedure. If you are
properly grounded when touching static-
u
p
g
rading a native Fibre Ch annel (FC)
l
i
b
rary, this clamp has already been
i
nstal ed. If you are upgrading a SCSI
l
ibrary, use the clamp that is already
i
n
s
t
al ed.
sensitive components.
3
I
n
s
pect the contents of the kit.
2
P
o
w
er off the library.
a
.
U
se your backup software to verify that the
O
p
en the back door of the library.
p
i
c
k
er is empty, or to empty the picker.
b
.
P
ress the power button located on the front of
t
he library behind the laptop tray and wait
u
n
t
i
l the OC P goes blank.
Caution: Before continuing with this
procedure, the library firmware must be at
version 1.02 or greater. Refer to the HP
StorageWorks Interface Manager and
Command View User Guide for detailed
procedures.
Note: These parts are only needed
Note: This part is not hot-swappable.
It is necessary to power down the library
Inspect the contents of the kit.
t
o replace this part.
during the initial library installation with
2
Power off the library.
native Fibre Channel (FC) drives, and they
a. Use your backup software to verify that the
picker is empty, or to empty the picker.
b. Press the power button located on the front of
the library behind the laptop tray and wait
until the OCP goes blank.
Note: The cable clamp provided is not
will not be used as part of this procedure.
needed for this procedure. If you are
upgrading a native Fibre Channel (FC)
library, this clamp has already been
installed. If you are upgrading a SCSI
library, use the clamp that is already
installed.
For more information, refer to the HP
StorageWorks ESL E-Series Unpacking
and Installation Guide.
Note: These FC cables are not used if
your library contains only LTO4 tape
Inspect the contents of the kit.
drives.
...Эта инструкция также подходит к моделям:
Устройства обработки данных - HP ESL 712e Ultrium Tape Library (805.7 kb)
Устройства обработки данных - HP StorageWorks ESL 286e 286 Slot SDLT Library (805.7 kb)
Устройства обработки данных - HP StorageWorks ESL 286e SDLT Tape Library (805.7 kb)
Устройства обработки данных - HP StorageWorks ESL 322e 322 Slot Ultrium Library (805.7 kb)