Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Document Outline
- Contents
- Preface
- General Information
- Installation Tasks
- Factory Defaults
- Installation Options
- Summary of Installation Tasks
- Task 1: Verify Installation Requirements
- Task 2: Install the Ethernet Hub
- Task 3: Install the Director
- Task 4: Configure Director Network Information
- Task 5: Install the Management Server
- Task 6: Configure the Management Server
- Task 7: Configure Director to the SAN Management Application
- Subtask A: Assign User Names and Passwords to SAN Management Application
- Subtask B: Identify the Director to the SAN Management Application
- Subtask C: Verify Director-to-SAN Management Application Communication
- Subtask D: Configure Feature Key
- Subtask E: Configure Open Systems Management Server (OSMS) or FICON Management Server (FMS)
- Configure OSMS
- Configure FMS (FICON)
- Task 8: Configure the Director at the Element Manager Application
- Subtask A: Set Director Date and Time
- Subtask B: Configure Director Identification
- Subtask C: Configure Director Management Style
- Subtask D: Configure Director Parameters
- Subtask E: Configure Fabric Parameters
- Subtask F: Configure Preferred Paths
- Subtask G: Configure Switch Binding
- Subtask H: Configure Director Ports
- Subtask I: Configure SNMP Trap Message Recipients
- Subtask J: Configure Threshold Alerts
- Subtask K: Configure OpenTrunking
- Subtask L: Enable SANpilot Interface and Telnet Access
- Subtask M: Configure, Enable, and Test E-mail Notification
- Subtask N: Configure and Enable Ethernet Events
- Subtask O: Configure, Enable, and Test Call-Home Notification
- Task 9: Configure SANtegrity Authentication (Optional)
- Task 10: Back Up Configuration Data
- Task 11: Configure the Director at the SANpilot Interface
- Subtask A: Connect Director to Internet or Ethernet LAN Segment
- Subtask B: Open the SANpilot Interface
- Subtask C: Configure Director Ports
- Subtask D: Configure BB Credit
- Subtask E: Configure Director Identification
- Subtask F: Configure Date and Time
- Subtask G: Configure Operating Parameters
- Subtask H: Configure Fabric Parameters
- Subtask I: Configure Network Information
- Subtask J: Configure SNMP
- Subtask K: Enable or Disable the CLI and SSH
- Subtask L: Enable or Disable OSMS and Host Control
- Subtask M: Change User Password
- Subtask N: Configure Port Binding
- Subtask O: Configure Switch Binding
- Configuring the Switch Binding Membership List
- Subtask P: Configure Fabric Binding
- Subtask Q: Enable or Disable Enterprise Fabric Mode
- Subtask R: Configure OpenTrunking
- Subtask S: Install Feature Keys
- Task 11: Cable Fibre Channel Ports
- Task 12: Configure Zoning
- Task 13: Connect the Director to a Fabric Element
- Task 14: Register with the McDATA File Center
- Maintenance Analysis Procedures (MAPS)
- Maintenance Analysis Procedures
- MAP 0000: Start MAP
- MAP 0100: Power Distribution Analysis
- MAP 0200: POST Failure Analysis
- MAP 0300: Server Application Problem Determination
- MAP 0400: Loss of Server Communication
- MAP 0500: FRU Failure Analysis
- MAP 0600: Port Card Failure and Link Incident Analysis
- MAP 0700: Fabric, ISL, and Segmented Port Problem Determination
- MAP 0800: Server Hardware Problem Determination
- Repair Information
- Factory Defaults
- Procedural Notes
- Obtaining Log Information
- Obtaining Port Diagnostic Information
- Performing Port Diagnostic Loopback Tests
- Performing Channel Wrap Tests (FICON)
- Swapping Ports (FICON)
- Collecting Maintenance Data
- Set the Director Online or Offline
- Blocking and Unblocking Ports
- Cleaning Fiber-Optic Components
- Power-On Procedure
- Power-Off Procedure
- IML, IPL, or Reset the Director
- Managing Firmware Versions
- Managing Configuration Data
- Installing or Upgrading Software
- Removal and Replacement Procedures (RRPs)
- Factory Defaults
- Procedural Notes
- Removing and Replacing FRUs
- RRP: Cable Management Assembly
- RRP: CTP2 Card
- RRP: Port Module Card (UPM and XPM)
- RRP: Optical Transceiver (SFP and XFP)
- RRP: Filler Blank (UPM and XPM)
- RRP: Power Supply
- RRP: RFI Shield
- RRP: SBAR Assembly
- RRP: Fan Module
- RRP: Power Module Assembly
- RRP: Backplane
- Illustrated Parts Breakdown
- Messages
- Event Code Tables
- Director Specifications
- Management Server and Ethernet Hub
- Restore Management Server
- Safety Notices (Multi-Lingual Translations)
- Glossary
- Index