Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Устройства обработки данных - HP MSA70 Array (70.93 kb)
Устройства обработки данных - HP MSA70 Array (303.69 kb)
Устройства обработки данных - HP MSA70 Array (283.85 kb)
Фрагмент инструкции
Site requirements
Installing enclosure into a rack
Select an installation site that meets the following requirements:
NOTE: When installing servers, HP recommends installing
•
Space
•
Temperature
all enclosures at the bottom of the rack. To optimize
•
Power
•
Rack
•
cabling access, avoid interleaving the enclosure and server
Grounding
•
Airflow
products.
Detailed installation site requirements for this product are
described in the HP StorageWorks 70 Modular Smart Array
1. Secure the front end of the rails to the rack.
Enclosure user guide located on the Documentation CD.
IMPORTANT: Do not remove the pins from the ends of the
Rack planning resources
rack rails unless you are converting the rails for use in
round-hole racks. These load-bearing pins are designed to
The rack resource kit ships with all HP branded or Compaq
fit through the holes without being removed.
branded 9000, 10000, and H9 series racks. For more
information on the content of each resource, see the rack
resource kit documentation.
IMPORTANT: Be sure that the scissor-type locking latches
engage the rack fully when the pins extend through the
If you intend to deploy and configure multiple servers in a single
holes marked with the template.
rack, see the white paper on high-density deployment at the HP
website: http://www.hp.com/products/servers/platforms.
NOTE: Identify the left (L) and right (R) rack rails by
Rack warnings
markings stamped into the sheet metal.
WARNING! To reduce the risk of personal injury or
damage to the equipment, be sure that:
•
The leveling jacks are extended to the floor.
•
The full weight of the rack rests on the
leveling jacks.
•
The stabilizing feet are attached to the rack
if it is a single-rack installation.
•
The racks are coupled together in multiple-
rack installations.
•
Only one component is extended at a time.
A rack may become unstable if more than
one component is extended for any reason.
WARNING! To reduce the risk of personal injury or
equipment damage when unloading a rack:
2. Secure the back end of the rails to the rack.
•
At least two people are needed to safely
unload the rack from the pallet. An empty
42U rack can weigh as much as 115 kg
(253 lb), can stand more than 2.1 m (7 ft)
tall, and may become unstable when being
moved on its casters.
•
Never stand in front of the rack when it is
rolling down the ramp from the pallet.
Always handle the rack from both sides.
Contents
•
MSA70 Enclosure
•
Rack mounting hardware kit
•
Power cords (2)
3. Slide the chassis into the rack.
•
SAS cable
4. Use the thumbscrews on the front of the chassis to secure it
•
Documentation kit
to the rack.
Installing options
Install any hard drives and hardware options before powering
up the enclosure. For complete information on installing hard
drives and options, see the user guide.
...Эта инструкция также подходит к моделям:
Устройства обработки данных - HP MSA70 Dual Domain (25) 300GB 2.5-inch DP SAS HDD 7.5TB Bundle (503.59 kb)
Устройства обработки данных - HP StorageWorks MSA70 with 25 72GB SAS SFF 1.8TB Bundle (503.59 kb)
Устройства обработки данных - HP StorageWorks MSA70 with 25 146GB SAS SFF 3.6TB Bundle (503.59 kb)