Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
DANGER - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubtas to whether the product is properly grounded. Do not modify the plug provided with the product if it will not fit the outlet; have a proper outlet installed by a qualified electrician. This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated below. A temporary adapter that looks like the adapter illustrated below may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet, (below) can be installed by a qualified electrician. The green colored rigid ear-lug, or the like, extending from the adapter, must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. Adapter Grounding Pin Grounded Outlet Box 4 ET288/ET388 Important Operation Instructions Important Operation Instructions • NEVER operate this treadmill without reading and completely understanding the results of any operational change you request from the computer. • Understand that changes in speed and incline do not occur immediately. Set your desired speed on the computer console and release the adjustment key. The computer will obey the command gradually. • NEVER use your treadmill during an electrical storm. Surges may occur in your household power supply that could damage treadmill components. • Use caution while participating in other activities while walking on your treadmill; such as watching television, reading, etc. These distractions may cause you to lose balance or stray from walking in the center of the belt, which may result in serious injury. • NEVER mount or dismount the treadmill while the belt is moving. Spirit treadmills start with at a very low speed and it is unnecessary to straddle the belt during start up. Simply standing on the belt during slow acceleration is proper after you have learned to operate the unit. • Always hold on to a handrail or hand bar while making control changes (incline, speed, etc.). Safety Tether Cord A safety tether cord is provided with this unit. It is a simple magnetic design that should be used at all times. It is for your safety should you fall or move too far back on the tread-belt. Pulling this safety tether cord will stop tread-belt movement. To Use: 1. Place the magnet into position on the round portion of the console control head. Your treadmill will not start and operate without this. Removing the magnet also secures the treadmill from unauthorized use. 2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note: The magnet has strong enough power to minimize accidental, unexpected stopping. The clip should be attached securely to make certain it does not come off. Be familiar with its function and limitations. The treadmill will stop, depending on speed, with a one to two step coast anytime the magnet is pulled off the console. 5 ET288/ET388 6 ET288/ET388 ASSEMBLY PACK CHECK LIST Assembly Instructions for ET288 #104 - 5/16.. x 1/2.. Button Head Socket Bolt (x12) #44 - Safety Key (x1) #105 - 5/16.. x 18mm Flat Washer (x4) #106 - 5/16.. x 23mm Curved Washer (x4) #107 - Combination M5 Allen Wrench & Phillips Head Screwdriver (x1) #108 - M6 Allen Wrench (x1) #109 - Lubricant (x1) 7 ET288/ET388 n STEP 1 Remove all the parts from the carton and lay the main base frame on a flat level surface. n STEP 2 Connect the cable from the base frame (53) to the cable in the right side upright tube (54) and slide the tube into the base frame tube. Be careful not to pinch the wire harness. Slide the left upright tube into the base frame tube. 53 54 n STEP 3 Install, and just hand tighten for now, all eight 5/16.. x 1/2.. socket head bolts (104) and the four 5/16.. flat washers (105) for the side bolts and four 5/16.. curved washers (106) for the front bolts. Tighten all eight bolts as tight as possible. 104 107 4 5 105 106 106 104 104 104 105 8 ET288/ET388 n STEP 4 This step is easier if you have someone else helping to hold the console while you connect the wires. Connect the handlebar incline switch wire (121) on the left side to the mating connector (122) of the console. Connect the handlebar speed switch wire (119) on the right side to the mating connector (120) of the console and then connect the computer cable (54) to the mating connector (55) of the console. 119 55 121 122 120 54 n STEP 5 Secure the console with four 5/16.. x 1/2.. socket head bolts (104). Do not pinch the wires when sliding the console onto the upright tubes. 104 104 107 9 ET288/ET388 ASSEMBLY PACK CHECK LIST Assembly Instructions for ET388 #130 - 5/16.. x 1/2.. Button Head Socket Bolt (12pcs) #75 - Safety Key (1pc) #30 - Lubricant (1) #131 - Combina...
Эта инструкция также подходит к моделям:Тренажеры - ET3881 (838.68 kb)