Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
• DUAL TIME • OPTIONAL 24-HR. TIME (MILITARY TIME) • WATER RESISTANT TO 300 FT. • NIGHT VISION™ ELECTROLUMINESCENT BACKLIGHTING KEY REFERENCES D - Clear B - Light A - Stop C - Mode E - Lap NORMAL TIME MODE (The term “mode” means the function status of the watch.) “Normal time mode” shows hours, minutes, seconds, day, date. To set time, see operating instructions on “How to Set Normal Time.” HOW TO SET NORMAL TIME, DATE AND 24-HOUR FORMAT Before setting time, you must be in “normal time mode.” Press and hold CLEAR button D while in “normal time mode” to enter the “set time” mode. Seconds digits will flash. Press LAP button E to reset the seconds digits to zero. If seconds are greater than 30, the minutes display will increase by one. Press MODE button C to cycle through the remaining digits to be set. Advance flashing digits by pressing LAP button E; hold for rapid advance. Retard digits by pressing STOP button A. The setting sequence is: seconds, hours, minutes, year, month, date, day, 12/24-hour format, and month-date or date-month. (Note: In the 12H mode, the “A” flag indicates time is in a.m.; “P” flag indicates time is in p.m.) Press CLEAR button D to complete setting at any time. Press LAP button E to change digits to larger format. message “FULL” will be displayed, and no additional lap times can be recorded. HOW TO RECALL LAP TIMES From “normal time mode”, enter the “recall mode” by pressing MODE button C twice. Mode prompt “CH-RC” will be displayed for one second. Segment one, and the day and date of segment one will flash momentarily, and then the first lap time of segment one will be displayed. Press STOP button A to select recorded segment of choice. Once a segment is selected, press LAP button E to view the contents of that specific segment. The display will show the lap number on the top row, the lap time on the middle row and the total elapsed time will appear on the bottom row. Press LAP button E to advance through the individual laps of that segment. After viewing the last lap of that segment, press STOP button A to view the next segment. TO CLEAR THE MEMORY While in the “recall mode”, press and hold CLEAR button D, (CLRHOLD will be displayed), to clear the segment that was last viewed. To clear all stored segments, press and hold CLEAR button D for six seconds; (CLR-HOLD-ALL will be displayed), and then “NO DATA” will be displayed. HOW TO SET AND OPERATE THE COUNTDOWN TIMER From “normal time mode”, press the MODE button C three times to enter the “timer mode”. Mode prompt “TIMER” will appear for one second. The timer has two different timing modes, and a range from one second to 23 hours, 59 minutes, 59 seconds. a. Countdown interval timer with five programmable segments (TMR1-5) b. Countdown stop (TMR) - will countdown from preset time and stop. Press STOP button A to select countdown timer choice. Press and hold CLEAR button D to enter the setting mode; seconds digits will flash. Press LAP button E to increase the flashing digit, press STOP button A to retard the flashing digit. Press MODE button C to advance from seconds, to minutes, to hours. Once the hours digits are set, interval timer 1-5 digit will flash. Press LAP button E to select the specific interval timer. Press CLEAR button D to complete setting of each individual interval timer. Continue with this procedure until all five interval timers are set. NOTE: It is not necessary to set all five interval timers. For example, if interval timer #3 is set to all zeroes, then the timer will skip to interval timer #4. The countdown-stop timer is set the same way as the interval timer. Once all desired timers are set, press CLEAR button D to exit the setting mode. The timer is now ready to use. Press LAP button E to start the timer. Press LAP button E again to change display format to indicate preset countdown time on the upper middle row, and time counting down on the lower middle row. Press STOP button A to stop the countdown timer. Press CLEAR button D to reset timer to preset time. NOTE: While using the interval timer, the number of completed interval cycles will be indicated on the lower row of the display (REP-00). HOW TO OPERATE THE ALARM The Xterra™ has an hourly chime and six different alarms: two daily alarms (AL-1 & AL-2), two weekday alarms (AL-3 & AL-4); and two date alarms (AL-5 & AL-6), which can be set in either normal time or dual time. Press MODE button C four times while in normal time mode to enter the alarm mode. Mode prompt “ALARM” will be displayed for one second. HOW TO SET AND VIEW DUAL TIME From “normal time mode”, press and hold STOP button A for three seconds. “T2 “ will appear in the upper right corner of the display. To set dual time, follow the same procedure used to set normal time, as indicated above. To return to normal time mode, press and hold STOP button A for three seconds. “T1” will appear on the upper right corner of the display. To view dual time from normal time mode, simply press STOP button A mo...
Эта инструкция также подходит к моделям:Часы - 716 Xterra (203.56 kb)