Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
See FIGURE 5. • Loosely assemble the TOP BOOM (7) to the FRONT UPRIGHT (2) using two 1/2 X 4” BOLTS (47), two 1/2” WASHERS (39), and two 1/2” LOCKNUTS (40). See FIGURE 5. • At this time, securely tighten all frame connections in this order: REAR UPRIGHT (9) to TOP BOOM (7), REAR UPRIGHT (9) to BASE (8), TOP BOOM (7) to FRONT UPRIGHT (2), and FRONT UPRIGHT (2) to BASE (8). 6 Insert two 3/4" FLANGE BEARINGS (29) into the TOP BOOM (7) as shown in FIGURE 6. Screw the ADJUSTABLE GLIDE (37) approximately 1/2” into the FRONT UPRIGHT (2) and tighten jam nut securely as shown. Attach the PRESS ARM (3) to the TOP BOOM (7) using the 3/4 X 7” SHAFT (13) as shown. Align the holes in the PRESS ARM (3) with the 3/4” FLANGE BEARINGS (29) and tap the SHAFT (13) in place with a rubber mallet. The SHAFT (13) should be flush with the outer edges of the PRESS ARM (3). Install two 5/16” SET SCREWS (50) into the top of the PRESS ARM (3) as shown in FIGURE 6. 1/2 1/2 1/2 1/2 1/2 1/2 0 I_L J_I_L 2 J_I_L 3 J_I_L 4 J_L 5 J_I_L J_I 7 STEP 7 • Loosely assemble two 4-1/2” PULLEYS (18) to the PRESS ARM (3) using two 3/8 X 7-1/2” BOLTS (51), four 3/8” WASHERS (38), four 3/8 X 1” SPACERS (32), and two 3/8” LOW HEIGHT LOCK NUTS (43) as shown in FIGURE 7. Once both PULLEYS are installed, you may securely tighten these two connections. • Securely tighten the two SET SCREWS (50) and insert two 2” SQ. END CAPS (56) into open ends of the PRESS ARM (3) as shown in FIGURE 7. 8 Securely assemble one SPRING PIN ASSEMBLY (35) and one 3 PRONG KNOB (33) to the FRONT UPRIGHT (2) as shown. Apply eight PARAGLIDES (57) to the INSIDE of the tube on the FRONT UPRIGHT (2) as shown. Securely assemble one SEAT PAD (12) to the PRESS SEAT (4) using two 3/8 X 2-3/4” BOLTS (48) and two 3/8” WASHERS (38) as shown in FIGURE 8. Insert the PRESS SEAT ASSEMBLY into the FRONT UPRIGHT (2) as shown. The PRESS SEAT height can be adjusted using the SPRING PIN (35) and can be secured with the 3 PRONG KNOB (33). Securely assemble one SEAT PAD (12) to the FRONT UPRIGHT (2) using two 3/8 X 3-3/4” BOLTS (45) and two 3/8” WASHERS (38) as shown in FIGURE 8. 1/2 1/2 1/2 1/2 1/2 1/2 0 I_L 1 J_L 2 J_L 3 J_L 4 J_L 5 J_L J_I 9 FIGURE 9 STEP 9 • Insert two 1/2” FLANGE BEARINGS (30) into the the LEG CURL EXT (1) as shown. • Assemble the LEG CURL EXT (1) to the FRONT UPRIGHT (2) using one 1/2 X 3” BOLT (46) and one 1/2” LOW HEIGHT LOCK NUT (42). (Note: Tighten this connection enough to remove excess play yet allow the LEG CURL EXT to rotate freely.) 10 Securely assemble the CALF BLOCK (10) to the BASE (8) using two 3/8 X 2-3/4” BOLTS (48), two 3/8” WASHERS (38), and two 3/8” LOCK NUTS (41) as shown in FIGURE 10. (Note: The CALF BLOCK can be assembled to either side of the BASE.) Apply the 4 X 14” NON-SKID STRIP (22) to the outside of the CALF BLOCK (10) as shown in FIGURE 10. Assemble the SWIVEL PULLEY BRACKET (5) to the BASE (8) using one 1/2” LOW HEIGHT LOCK NUT (42) as shown in FIGURE 10. (Note: Tighten this connection enough to remove excess play yet al1owing SWIVEL PULLEY BRACKET to rotate freely.) Securely assemble one 3-1/2” PULLEY (19) to the SWIVEL PULLEY BRACKET (5) using one 3/8 X 1-3/4” BOLT (49) and one 3/8” LOCK NUT (41) as shown in FIGURE 10._ 1/2 1/2 1/2 1/2 1/2 1/2 0 I_L 1 J_L 2 J_L 3 J_L 4 J_L 5 J_L 6 J_I 11 STEP 11 • Attach two 4 X 7” ROLLER PADS (15) to the FRONT UPRIGHT (2) using one 3/4 X 16” TUBE (14) and two 3/4” STARLOCK COLLARS (52) as shown in FIGURE 11. • Attach two 4 X 7” ROLLER PADS (15) to the PRESS SEAT (4) using one 3/4 X 16” TUBE (14) and two 3/4” STARLOCK COLLARS (52) as shown in FIGURE 11. • Attach two 4 X 7” ROLLER PADS (15) to the LEG CURL EXT (1) using one 3/4 X 16” TUBE (14) and two 3/4” STARLOCK COLLARS (52) as shown in FIGURE 11. STEP 12 • Securely assemble one 4-1/2” PULLEY (18) to the FLOATING PULLEY BRACKET (6) using one 3/8 X 1-3/4” BOLT (49) and one 3/8” LOCK NUT (41) as shown in FIGURE 12. 12 STEP 13 • Securely assemble the ball end of the WEIGHT STACK CABLE (26) and one 3-1/2” PULLEY (19) to the TOP BOOM (7) using one 3/8 X 2-3/4” BOLT (48), two 3/8” FLANGE SPACERS (36), and one 3/8” LOCK NUT (41) as shown in FIGURE 13. (Note: Loop the CABLE around the PULLEY prior to inserting it into the slot in the TOP BOOM.) • Route the threaded end of the WEIGHT STACK CABLE (26) underneath the upper press arm pulley. Securely assemble the WEIGHT STACK CABLE (26) and one 3-1/2” PULLEY (19) to the FRONT UPRIGHT (2) using one 3/8 X 2-3/4” BOLT (48), two 3/8” FLANGE SPACERS (36), and one 3/8” LOCK NUT (41) as shown in FIGURE 13. (Note: Loop the CABLE around the PULLEY prior to inserting it into the upper slot in the FRONT UPRIGHT.) • Route threaded end of the WEIGHT STACK CABLE (26) around the lower press arm pulley, through the lower slot in the FRONT UPRIGHT (2) , and down through the large hole in the FRONT UPRIGHT (2). Securely assemble the WEIGHT STACK CABLE ...