Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Remove the SHROUD from the 425104 HOME GYM. See FIGURE 1. 3 STEP 2 • If the 445104 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the SHROUD as shown in FIGURE 2. 1/2 1/2 1/2 0 I_L J_I_L 2 J_I_L 1/2 1/2 1/2 3 J_I_L 4 J_L 5 J_I_L 6 J_I 4 • Remove two 3/8” LOCK NUTS, two 3/8” HEX NUTS, two SWIVEL SNAP (68) (keep elastic cords attached), two 3/8 X 1/2” SPACERS, and one 3/8” THREADED SHAFT from the bracket on the BASE as shown in FIGURE 3. • Discard the two 3/8 X 1/2” SPACERS. 5 Assemble the two previously removed 3/8” HEX NUTS, two previously removed SWIVEL SNAPS, one 3-1/2” PULLEY (2), and two previously removed 3/8” LOCK NUTS to the previously removed 3/8” THREADED SHAFT as shown in FIGURE 4. Remove one 3/8 X 2” BOLT, two 3/8” WASHERS, one 2-7/8” L-BRACKET, one 4-1/2” PULLEY, and one 3/8” LOCK NUT from the upper flat on the BASE as shown in FIGURE 5. 1/2 0 I_L J_I_L 1/2 | 1/2 2 _l_I_l_ | 1/2 | 1/2 3 I 4 J_I_I_I_I_I_l_ 1/2 5 J_I_L 6 J_I 6 STEP 6 • SECURELY assemble the previously removed 4-1/2” PULLEY to the BASE using one 3/8 X 2-1/4” BOLT (14), two previously removed 3/8” WASHERS, one previously removed 2-7/8” L-BRACKET, one SWIVEL SNAP (6), one 3/8” HEX NUT (9), and one previously removed 3/8” LOCK NUT. See FIGURE 6. • If the 445104 SECOND STACK OPTION is installed follow STEP 7B . • Remove one 3/8” WASHER and one 3/8” LOCK NUT from the 3/8” THREADED SHAFT on the TOP BOOM. • SECURELY assemble one 2” PULLEY (5) to the 3/8” THREADED SHAFT on the TOP BOOM using one previously installed 3/8” WASHER, one 3/8” HEX NUT (9) and one previously installed 3/8” LOCK NUT as shown in FIGURE 7A. 7 STEP 7B • If the 445104 SECOND STACK OPTION is NOT installed proceed to STEP 8 . • SECURELY assemble one 3/8 X 1” BOLT (16), one 3/8” WASHER (10), one 2” PULLEY (5) and one 3/8” LOCK NUT (11) to the bracket on the TOP BOOM as shown in FIGURE 7B. STEP 8 • SECURELY attach one 3-1/2” PULLEY (2) to the FRONT LEG (1) using one 3/8 X 2-1/4” BOLT (14), two 3/8” WASHERS (10), and one 3/8” LOCK NUT (11). See FIGURE 8. • Attach the open end of PRESS LINK CABLE (8) to the QUICK DISCONNECT LINK (3). See FIGURE 8. • SECURELY tighten the QUICK DISCONNECT (3) to the tab on the FRONT LEG (1) as shown in FIGURE 8. 1/2 1/2 1/2 1/2 1/2 1/2 0 I_L J_I_L 2 _L 3 _L 4 J_L 5 _L J_I 8 STEP 9 • SECURELY attach the LEG PRESS to the FRONT LEG (1) using two 1/2” X 3” BOLTS (15), two 1/2” WASHERS (12), and two 1/2” LOCK NUTS (13). See FIGURE 9. • Route LEG PRESS CABLE (8) around the 3-1/2” PULLEY on the LEG PRESS and UNDER the 3-1/2” PULLEY on the FRONT LEG (1) as shown in FIGURE 9. 9 SECURELY attach the FRONT LEG (1) to 425 BASE using two 1/2 X 3” BOLTS (15), two 1/2” WASHERS (12) and two 1/2” LOCK NUTS (13). See FIGURE 10. Route LEG PRESS CABLE (8) under the 3-1/2” PULLEY on the 425 BASE as shown in FIGURE 10. | 1/2 | 1/2 0 I 1 1_I_I_I_I_L_ 1/2 2 I 3 J_I_I_I_I_I_L 1/2 1/2 1/2 4 5 16 J_I_I__I_I_I_I_I_I 10 • Run the LEG PRESS CABLE through the correct hole on the d-ring and attach one KEYHOLE CLEVIS to the end of the LEG PRESS CABLE. See FIGURE 11 & DETAIL 11. (NOTE: If the 445101 SECOND STACK kit is installed, evenly space the LAT & LEG EXT. 11 • Assemble the 72” ELASTIC CORD (7) from the LEG PRESS CABLE (8) around the 2” PULLEY (5) in the TOP BOOM as shown in 12 • SECURELY attach the four previously removed 3/8 X 1” BUTTON HEAD CAP SCREWS to the rear SHROUD. See FIGURE 14. • The 832 LEG PRESS is equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit from the machine. To use, you must slightly push against the foot plates to take tension off the pin. Thank you for purchasing the Parabody 435104 Leg Press Adapter Kit. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. 13...