Оценок - 3, средний балл: 4.3
(
)
)
|
Фото и характеристики Vision Fitness R2750HRT |
Фрагмент инструкции
Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 ©2006 Vision Fitness. All Rights Reserved. 11.06 AG18.46PRD REV1 TOOLS & PARTS INCLUDED 5mm T-Shaped Wrench 15mm Pedal Wrench Screwdriver 5mm L-Shaped Wrench 4mm L-Shaped Wrench PARTS BOX Console Mast Cover Water Bottle Heart Rate Chest Strap Color-coded Hardware Bags Pedals/Straps Owner’s Guide Assembly Guide Warranty Card HARDWARE INCLUDED ORANGE BAG GREEN BAG PINK BAG BLUE BAG M8 x 15L Bolt Quantity: 6 M8 x 20L Bolt Quantity: 2 M8x65L Bolt Quantity: 2 M8 Lock Washer Quantity: 4 M8 x 15L Bolt Quantity: 2 M8 Lock Washer Quantity: 2 BLACK BAG M6 x 55L Bolt Quantity: 4 M6 Lock Washer Quantity: 4 M8 x 20L Bolt Quantity: 8 M8 Lock Washer Quantity: 8 YELLOW BAG M5 x 35L Bolt Quantity: 2 M5 Lock Washer Quantity: 2 M10 x 12L Set Screw Quantity: 1 STEP 2 • Slide the console mast boot onto the console mast. • Unfold the wire harness and heart rate wires located in the console mast frame bracket. Attach the wire tie coming from the bottom of the console mast to the wire harness and heart rate wires. Pull the wire tie with wire harness and heart rate wires up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the console mast to the frame bracket with six bolts (M8x15L). Tighten with the 5mm T-Shaped wrench. Insert a set screw (M10x12L) to the front edge of the mast and tighten until snug with the 5mm T-shaped wrench. • Slide the console mast boot down and snap it into place on the side cover. BLUE BAG STEP 3 • Mount the upper handlebars to the console mast using two lock washers (M8) and two bolts (M8x15L). Tighten with the 5mm T-Shaped wrench. • Remove the four mounting screws from the back of the console. Connect the wire harness and heart rate wires that come from the console mast into the plugs located in the back of the console. Attach the console to the mast with the four screws removed earlier. • Remove the battery cover on the back side of the console. Plug in the 9-volt battery. Re-attach the battery cover. PINK BAG STEP 1 • Install the rear foot with the four lock washers (M8), two inside bolts (M8x65L), and two outside bolts (M8x20L). Tighten with the 5mm T-Shaped wrench. ORANGE BAG A s s e m b l y G u i d e R2750HRT COMMERCIAL FITNESS BIKES STEP 1 STEP 4 • Remove the two socket head bolts from the sliding seat adjustment bracket. Slide the seat adjustment handle between the teeth of the seat adjustment bracket. Re-insert the two socket head bolts and tighten with the 4mm Lshaped wrench. • Attach the seat frame to the sliding seat bracket using four lock washers (M8) and four bolts (M8x20L) and the 5mm T-Shaped wrench. • Connect Wires A on the seat handlebar to Wires B on the sliding seat bracket. Connect the wire harness coming from the seat frame to the wire harness in the handlebars. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four bolts (M8x20L). Tighten with the 5mm T-Shaped wrench. GREEN BAG STEP 2 To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws and bolts are in place and partially threaded in before completely tightening any ONE screw or bolt. STEP 5 STEP 4 STEP 5 • Mount the seat bottom to the seat frame with four bolts (M6x55L) and four lock washers (M6). Tighten with the 4mm L-shaped wrench. BLACK BAG STEP 3 Wires B Wires A STEP 6 • Attach the left and right pedals to the left and right crank arms. Tighten the pedals using the 15mm Pedal Wrench. • Secure the Accessory Tray to the seat handlebar with two bolts (M5x35L) and two lock washers (M5). Be careful when inserting the bolts to clear the wires inside the handlebar to prevent damage. Tighten with the screwdriver. YELLOW BAG STEP 6 Seat Bottom Console Mast Handlebar Seat Handlebar Seat Frame Console Mast Console Mast Boot Frame Bracket Rear Foot Accessory Tray Pedal Sliding Seat Bracket ...