Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
• After installation, check that the brake lamps, winkers, and wipers work properly. NOTE • Do not connect cables and leads to both RCA cable input jacks and the speaker level input terminals simultaneously, for this may cause malfunction or damage. A channel Left speaker A channel Right speaker B channel Right speaker B channel Left speaker A channel Speaker (Bridged) B channel Speaker (Bridged) A channel input B channel input Terminal cover ¦ Power wire and Speaker wire connection • RCA cable Connections • Speaker level input Connections Power control wire .... Genuine-accessory car stereo (No line output center unit etc.) ACC Battery Car fuse box Cable Color of the connector A channel Left 9 White · White/Black A channel Right 9 Gray · Gray/Black B channel Left 9 Green · Green/Black B channel Right 9 Purple · Purple/Black English 5 Controls This is a 4 channel amplifier including 2 stereo amplifiers in a body. One amplifier is referred to as amplifier A and the other is amplifier B. This unit is compatible with a large variety of systems by combining the switches and functions described in the following. 1 Fuse (40 A) NOTE If you can’t find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. NOTE Controls the unit power. Be sure to connect it with all the systems. 5 Speaker output terminals (A.ch/B.ch) • Stereo Connections: When you wish to use the unit as a stereo amplifier, stereo connections are used. The speakers to be connected should have an impedance of 2. or greater. When multiple speakers are to be connected, ensure that the combined impedance is 2. or greater for each channel. • Bridged Connections: When you wish to use the unit as a high-output monaural amplifier, bridged connections are used. (Make connections to the LEFT channel 9 and the RIGHT channel · SPEAKER OUTPUT terminals.) The speakers to be connected should have an impedance of 4. or greater. When multiple speakers are to be connected, ensure that the combined impedance is 4. or greater. 2CAUTION The rated input of the speakers should be no less than the maximum output of the amplifier. Otherwise malfunction may result. 6 RCA cable ground lead terminal When using an RCA cable with a ground lead attached, connect the ground lead to this terminal. 7 Speaker level input terminals NOTE • The genuine-accessory car stereo shall have a maximum power output of no more than 40 W. • Do not connect the speaker output leads from a power amplifier (Optional) to the speaker level input terminals of this unit, for this may cause malfunction or damage. • Do not connect cables and leads to both RCA cable input jacks and the speaker level input terminals simultaneously, for this may cause malfunction or damage. • Connect the power control lead to a power supply which can be turned ON/OFF by the ignition key switch (ACC line). With this connection, shock noise may be generated when the power of the genuine-accessory car stereo is switched ON/OFF. 8 LINE IN terminal (A.ch/B.ch) 9 LINE OUT terminal These jacks output respectively the signals input to amplifiers A and B. They always output the stereo signals regardless of the position of the "OPERATION" switch. 0 Power indicator When the power is turned on, the Power indicator lights. If the Power indicator does not light when the power is turned on, the protection function may be activated. Check whether there is any indication of trouble. (See page 2) ! FILTER switch (A.ch) This switch allows to apply high-pass filtering to the speaker outputs. • HPF (High-Pass Filter) position: The filter outputs the band of higher frequencies than the frequency set with the "HPF FREQUENCY" control. • OFF position: The entire bandwidth is output without filtering. @ OPERATION switch (A.ch/B.ch) The amplification methods of the signals input to amplifiers A and B can be selected independently according to the setting of this switch. • STEREO position: The amplifier can be used as a stereo amplifier. • MONO (Lch) position: Amplifies the signal input from the left side only. Set to this position and make bridged connections to use as a high-power monaural amplifier. (The input right signal is not output.) # INPUT SELECTOR switch This switch selects the input method of the signals to be amplified by amplifiers A and B. • A B position: Amplifies both of the signals input to amplifiers A and B. • A position: Amplifies only signal input amplifier A with both amplifiers A and B. $ FILTER switch (B.ch) This switch allows to apply high-pass or low-pass filtering to the speaker outputs. • HPF (High-Pass Filter) position: The filter outputs the band of higher frequencies than the frequency set with the "HPF FREQUENCY" control. • OFF position: The entire bandwidth is output without filtering. • LPF (Low-Pass Filter) position: The filter outputs the band of lower frequencies than the frequency set with the "LPF FREQUENCY...
Эта инструкция также подходит к моделям:Автоусилители - KAC-8402 (1.65 mb)