Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Secure it with two M10 x 2 .” Carriage Bolts (#85), O .” Washers (#99), and M10 Aircraft Nuts (#96). G.)Secure the Left Vertical Beam (#5) to the Upper Frame (#6) and Rear Vertical Frame (#4) with two M10 x 2 .” Carriage Bolts (#84), O .” Washers (#99), and M10 Aircraft Nuts (#96). H.) DO NOT tighten all Nuts and Bolts yet. 9 DIAGRAM 4 10 STEP 5 (See Diagram 5) A.) Attach the Left Seat Support (#8) to the Left Vertical Beam (#5). Secure it with two M10 x 2 .” Carriage Bolts (#85), one 4 3/8” x 1 .” Bracket (#73), two O .” Washers (#99), and two M10 Aircraft Nuts (#96). B.) Attach the Left Seat Support (#8) to the Left Base Frame (#2). Secure it with a M10 x 2 .” Carriage Bolt (#85), O .” Washer (#99), and M10 Aircraft Nut (#96). C.) Attach the Leg Press Frame (#14) to the Left Base Frame (#2). Secure it with one M12 x 3 .” Hex Bolt (#89), two O1” Washers (#100), and one M12 Aircraft Nut (#97). D.) Attach the Leg Press Adjustment Frame (#15) to the Leg Press Plate (#28). Secure it with one M10 x 2 .” Carriage Bolt (#85), O .” Washer (#99), and M10 Aircraft Nut (#96). E.) Insert the Leg Press Adjustment Frame (#15) into the opening on the Leg Press Frame (#14). Use a M18 Lock Knob (#61) to secure it at desired position. 11 STEP 6 (See Diagram 6) A.) Attach the Front Press Base (#10) to the Right Base Frame (#1). Secure it with one M10 x 9 .” Front Press Axle (#49), two O .” Washers (#99), and two M10 Aircraft Nuts (#96). B.) Attach two Front Press Frames (#13) onto the bracket on the Front Press Base. Secure them to the Front Press Base with four M10 x 2 .” Carriage Bolts (#85), O .” Washers (#99), and M10 Aircraft Nuts (#96). C.) Securely tighten all Nuts and Bolts previously installed. DIAGRAM 6 12 STEP 7 (See Diagram 7) A.) Attach the Butterfly Support Frame (#11) to the front of Right Vertical Frame (#3). Attach the Butterfly Pulley Support (#12) to the back of Right Vertical Frame. Align the holes and secure them with two M10 x 2 .” Carriage Bolts (#85), O .” Washers (#99), and M10 Aircraft Nuts (#96). B.) Attach two Swivel Pulley Brackets (#23) to the Butterfly Pulley Support (#12). Secure each Bracket with one M12 x 4 3/8” Hex Bolt (#88), two O1” Washers (#100), and one M12 Aircraft Nut (#97). Do not over tighten the nut and bolt. The brackets need to swivel. C.) Insert the Axle on the Right Butterfly (#18) through a Butterfly Adjustment Frame (#26) into the hole on the Butterfly Support Frame (#11). Secure it with one O1 .” Washer (#101), Lock Ring (#53), M6 x 1 .” Allen Bolt (#93), and M6 Aircraft Nut (#95). D.) Thread a T-shaped Pull Pin (#58) through the hole on the Right Butterfly. Use the Pin to adjust the Butterfly position. E.) Attach a Butterfly Arm Pad (#35) to the Right Butterfly. Secure it with two M8 x 2 3/8” Allen Bolts (#91) and O 5/8” Washers (#98). F.) Repeat procedures C, D and E above to install the Left Butterfly. 13 STEP 8 (See Diagram 8) A.) Attach the Vertical Press Frame (#20) to the Rear Vertical Frame (#4). Secure it with one M10 x 4 7/8” Vertical Press Axle (#48), two O .” Washers (#99), and two M10 x 5/8” Allen Bolts (#80). B.) Place the Vertical Press Frame rest against the rubber bumper on the Left Vertical Beam (#5). DIAGRAM 8 14 CABLE LOOP DIAGRAM 15 STEP 9 (See Cable Loop Diagram & Diagram 9) A.) Attach the 108” Upper Cable (#37) to the front opening on the Upper Frame (#6). Attach a Pulley (#56) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#83), two Pulley Bushings (#55), and one M10 Aircraft Nut (#96). Draw the Cable towards the back of the machine. Note: Make sure the Ball Stopper is underneath the frame. B.) Attach a Pulley to the bracket on the Upper Frame. Secure it with one M10x1 .” Allen Bolt (#82), two ..” Washers (#99), one 2 7/8” L-shaped Pulley Bracket (#50), and one M10 Aircraft Nut (#96). Pull the Cable over the Pulley then downward. Install a Pulley to a Flat Double Floating Pulley Bracket (#25). Let the bracket hanging for now. C.) Draw the Cable around the Pulley then upward to the second open bracket on the Upper Frame. Install another Pulley with a U-shaped Pulley Bracket (#51). D.) Draw the Cable around the Pulley then downward to the Selector Rod (#29). Securely thread the end of the Cable through the Weight Selector Pin (#46) into the Selector Rod. Use the Nut at the end of the Cable to tighten down the Bolt. 16 STEP 10 (See Cable Loop Diagram & Diagram 10) A.) Clip one end of the 106” Butterfly Cable (#38) to the slot on the Left Butterfly Adjustment Frame. Draw the Cable through the slot then to the open left Swivel Pulley Bracket (#23). B.) Attach a Pulley (#56) to the bracket. Secure it with one M10 x 1 .” Allen Bolt (#82), two . .” Washers (#99), and one M10 Aircraft Nut (#96). C.) Draw the Cable around the Pulley then downward. Install a Pulley to the Angled Double Floating Pulley Bracket (#24). Install another Pulley then let the Bracket hanging for now. D.) Draw the Cable upward to the right Swivel Pulley Bracket. Install ano...